Skip to content

Effect of Polypropylene Fiber Addition on Properties of Geopolymers Made by 3D Printing for Digital Construction (2018-11)

10.3390/ma11122352

 Nematollahi Behzad, Vijay Praful,  Sanjayan Jay,  Nazari Ali,  Xia Ming,  Nerella Venkatesh,  Mechtcherine Viktor
Journal Article - Materials, Vol. 11, Iss. 12

Abstract

This paper investigates the effect of polypropylene (PP) fibres on the fresh and hardened properties of 3D-printed fibre-reinforced geopolymer mortars. Different percentages of PP fibres ranging between 0.25% and 1.00% by volume were added to an optimised geopolymer mixture. All samples showed reasonable workability and extrudability. In addition, shape-retention ability in the fresh state was investigated as a major requirement for 3D-printing. The compressive strength of the printed specimens was tested in the hardened state in three loading directions, viz. longitudinal, perpendicular, and lateral. The flexural strength of samples was also tested in the longitudinal and lateral directions. In addition, the interlayer bond strength was investigated. Fibre addition seems to influence compressive strengths positively only when the loading is perpendicular to the interface plane. This is due to the preferential fibre alignment parallel to the direction of extrusion. The addition of fibre significantly enhanced the flexural performance of the printed samples. The use of fibre dosages of 0.75 and 1.00 vol % caused deflection-hardening behaviour of the 3D-printed geopolymers and, hence, a significantly higher fracture energy in comparison to specimens without fibre or with lower fibre content. However, an increase in the fibre volume caused some minor reduction in interlayer bond strength. With respect to properties in the fresh state, higher fibre volumes caused better shape-retention ability in the printed samples. The results indicate the possibility of printing fibre-reinforced geopolymers which meet all the necessary properties in both the fresh and hardened states.

19 References

  1. Cesaretti Giovanni, Dini Enrico, Kestelier Xavier, Colla Valentina et al. (2013-08)
    Building Components for an Outpost on the Lunar Soil by Means of a Novel 3D Printing Technology
  2. Hambach Manuel, Volkmer Dirk (2017-02)
    Properties of 3D Printed Fiber-Reinforced Portland-Cement-Paste
  3. Khoshnevis Behrokh (2003-11)
    Automated Construction by Contour Crafting:
    Related Robotics and Information Technologies
  4. Le Thanh, Austin Simon, Lim Sungwoo, Buswell Richard et al. (2012-01)
    Hardened Properties of High-Performance Printing Concrete
  5. Le Thanh, Austin Simon, Lim Sungwoo, Buswell Richard et al. (2012-01)
    Mix-Design and Fresh Properties for High-Performance Printing Concrete
  6. Lloret-Fritschi Ena, Shahab Amir, Linus Mettler, Flatt Robert et al. (2014-03)
    Complex Concrete Structures:
    Merging Existing Casting Techniques with Digital Fabrication
  7. Marchment Taylor, Xia Ming, Dodd Elise, Sanjayan Jay et al. (2017-07)
    Effect of Delay-Time on the Mechanical Properties of Extrusion-Based 3D Printed Concrete
  8. Mechtcherine Viktor, Grafe Jasmin, Nerella Venkatesh, Spaniol Erik et al. (2018-05)
    3D Printed Steel-Reinforcement for Digital Concrete Construction:
    Manufacture, Mechanical Properties and Bond Behavior
  9. Mechtcherine Viktor, Nerella Venkatesh (2018-04)
    Incorporating Reinforcement in 3D-Printing with Concrete
  10. Nematollahi Behzad, Xia Ming, Sanjayan Jay (2017-07)
    Current Progress of 3D Concrete Printing Technologies
  11. Ogura Hiroki, Nerella Venkatesh, Mechtcherine Viktor (2018-08)
    Developing and Testing of Strain-Hardening Cement-Based Composites (SHCC) in the Context of 3D Printing
  12. Panda Biranchi, Paul Suvash, Lim Jian, Tay Yi et al. (2017-08)
    Additive Manufacturing of Geopolymer for Sustainable Built Environment
  13. Rael Ronald, Fratello Virginia (2011-10)
    Developing Concrete Polymer Building Components for 3D Printing
  14. Sanjayan Jay, Nematollahi Behzad, Xia Ming, Marchment Taylor (2018-04)
    Effect of Surface Moisture on Inter-Layer Strength of 3D Printed Concrete
  15. Schutter Geert, Lesage Karel, Mechtcherine Viktor, Nerella Venkatesh et al. (2018-08)
    Vision of 3D Printing with Concrete:
    Technical, Economic and Environmental Potentials
  16. Soltan Daniel, Li Victor (2018-03)
    A Self-Reinforced Cementitious Composite for Building-Scale 3D Printing
  17. Tay Yi, Panda Biranchi, Paul Suvash, Mohamed Nisar et al. (2017-05)
    3D Printing Trends in Building and Construction Industry:
    A Review
  18. Wangler Timothy, Lloret-Fritschi Ena, Reiter Lex, Hack Norman et al. (2016-10)
    Digital Concrete:
    Opportunities and Challenges
  19. Wu Peng, Wang Jun, Wang Xiangyu (2016-04)
    A Critical Review of the Use of 3D Printing in the Construction Industry

199 Citations

  1. Tushar Fazlul, Hasan Mehedi, Hasan Kamrul, Mawa Jannatul et al. (2026-01)
    Factors Affecting Flowability and Rheological Behavior of 3D Printed Concrete:
    A Comprehensive Review
  2. Dubey Pratik, Maurya Madan (2026-01)
    A Comprehensive Review of 3D Printing in Construction:
    Technology, Materials, and Digital Workflow
  3. Talukdar A., Belek Fialho Teixeira Müge, Fawzia Sabrina, Zahra Tatheer et al. (2026-01)
    Investigation on the Fresh and Mechanical Properties of Low Carbon 3D Printed Concrete Incorporating Sugarcane Bagasse Ash and Microfibers
  4. Guerrero Ana, Asensio Eloy, Fernández Fernando (2025-12)
    Large‐Format Additive Manufacturing with Cement and Clays:
    Characterization Methods
  5. Hasan Md, Xu Jie, Uddin Md (2025-11)
    A Critical Review of 3D Printed Fiber-Based Geopolymer Concrete:
    Fresh Properties, Mechanical Performance, and Current Limitations
  6. Hasani Alireza, Dorafshan Sattar (2025-11)
    Evaluation of Fresh, Hardened, and Durability Properties of Three-Dimensional Concrete Printed Pipes
  7. Garshasbi Sajad, Mousavi Seyed, Dehestani Mehdi, Nazarpour Hadi (2025-10)
    Sustainable Production of 3D Concrete Printing Using Agricultural Waste Fibers
  8. Öztürk Ece, Borgianni Yuri, Ince Ceren (2025-10)
    3D Printing in the Construction Sector:
    Identification of Key Topics, Technologies, Applications and Relevant Factors Discussed in the Literature
  9. Safdar Gardezi Syed, Tanyildizi Harun, Haroglu Hasan, Coskun Ahmet (2025-09)
    Acid Attack Performance of 3D Printing Nano-ZnO Modified Geopolymer Mortar
  10. Zhou Juanlan, Shi Xiangwen, Zheng Hongrun, Jin Ruoyu et al. (2025-09)
    Investigating the Effects of Hybrid PVA/BF Fibers in Low-Carbon 3D Printed Concrete with Recycled Aggregates:
    Rheology, Strength, and Anisotropy
  11. Alonso-Cañon Sara, Blanco-Fernandez Elena, Cuesta-Astorga Eva, Indacoechea-Vega Irune et al. (2025-09)
    Selection of the Best 3D Printing High-Performance Mortars Using Multi-Criteria Analysis
  12. Luo Surong, Jin Wenhao, Zhang Zhaorui, Zhang Kaijian (2025-09)
    Constitutive Relationship of 3D Printed Fiber Reinforced Recycled Sand Concrete Under Uniaxial Compression
  13. Bradford Katy, Gentry Russell, Alon Lola, Kurtis Kimberly (2025-08)
    Construction 3D Printing Material Selection:
    Minimizing Cost and Carbon Footprint of Residential Wall Assemblies
  14. Motiani Ronak, Sylvain Saha, Dalal Sejal, Vora Jay et al. (2025-08)
    Innovative Reinforcement Techniques for 3D-Printed Concrete:
    The Impact of Shape Memory Alloys on Flexural Strength and Crack Mitigation
  15. Pan Keheng, Cheng Yinhan, Qu Guangfei, Yuan Zheng et al. (2025-07)
    Development and Optimization of Geopolymer-Based 3D Printing Materials Utilizing Industrial Solid Waste:
    Rheological Properties and Practical Applications
  16. Gerges Isabelle, Farraj Faten, Youssef Nicolas, Antczak Emmanuel et al. (2025-07)
    Methodologies to Design Optimum 3D Printable Mortar Mix:
    A Review
  17. Mim Nusrat, Hosan Anwar, Shaikh Faiz, Sarker Prabir (2025-07)
    Rheological and Early Age Mechanical Properties of 3D Printed Concrete Containing Copper Heap Leach Residue as Fine Aggregate
  18. Raza Muhammad, Kravchenko Ekaterina, Besklubova Svetlana, Lazorenko Georgy et al. (2025-07)
    3D Printing of Recycled Materials for Sustainable Construction:
    A Comprehensive Economic and Life Cycle Assessment
  19. Alkhawaldeh Ayah, Alhassan Mohammad, Sawalha Ansam, Betoush Nour et al. (2025-06)
    Integration of 3D Printing and Machine Learning in Sustainable Construction:
    Feasibility and Challenges
  20. Srinivas Dodda, Panda Biranchi, Suraneni Prannoy, Sitharam Thallak (2025-06)
    Mix Design Optimization of 3D-Printed Cementitious Composites for Marine Applications:
    Impact of Binder Composition, Accelerated Carbonation, and PVA Fibers on Strength and Durability
  21. Zhao Yu, Shen Guanghai, Zhu Lingli, Ding Yahong et al. (2025-06)
    Enhancing Interfacial Bonding and Pore Structure Optimization in 3D-Printed High-Strength ECC with Steel-PE Hybrid Fibers
  22. Hopkins Ben, Si Wen, Khan Mehran, McNally Ciaran (2025-06)
    Recent Advancements in Polypropylene Fiber-Reinforced 3D-Printed Concrete:
    Insights into Mix Ratios, Testing Procedures, and Material Behaviour
  23. Raza Ali, Junjie Zhang, Fan Jiahui, Umar Muhammad et al. (2025-05)
    Comprehensive Study on the Microstructural and Mechanical Performance of 3D-Printed Engineered Cementitious Composites with Yellow River Sand Integration
  24. Mishra Jyotirmoy, Babafemi Adewumi, Combrinck Riaan (2025-04)
    Limitations and Research Priorities in 3D-Printed Geopolymer Concrete:
    A Perspective Contribution
  25. Dabbaghisouraki Farshad, Tanhadoust Amin, Nehdi Moncef (2025-04)
    Fiber Reinforcement Strategies in 3D Concrete Printing:
    Addressing Challenges and Identifying Research Gaps
  26. Tanyildizi Harun, Seloglu Maksut, Bakri Abdullah Mohd, Razak Rafiza et al. (2025-04)
    The Rheological and Mechanical Properties of 3D-Printed Geopolymers:
    A Review
  27. Gulati Hemant, Lu Tianxing (2025-03)
    Customized 3D Printable Concrete:
    A Systematic Review of Challenges, Methodologies, and Adoption Strategies
  28. Nassrullah Ghaith, Ali Mohd, Rub Rashid, Cho Cung-Suk et al. (2025-03)
    Optimizing Cement-Based Material Formulation for 3D Printing:
    Integrating Carbon Nanotubes and Silica Fume
  29. Xia Kailun, Chen Yuning, Zhang Zedi, Wang Wei et al. (2025-03)
    In-Situ Crosslinked Nano-SiO2 Reinforced Alginate Bio-Textile for Mitigating Plastic Shrinkage in 3D Printed Concrete
  30. Liu Han, Laflamme Simon, Cardinali Amelia, Lyu Ping et al. (2025-03)
    Enhancing 3D-Printed Cementitious Composites with Recycled Carbon Fibers from Wind Turbine Blades
  31. Şahin Hatice, Kaya Yahya, Akgümüş Fatih, Mardani Naz et al. (2025-03)
    Degradation of Mechanical Properties of 3D Fiber Reinforced Printed Concrete Mixtures Exposed to Elevated Temperatures
  32. Zhu Binrong, Zhang Yuhang, Ye Huzi, Wei Yang et al. (2025-03)
    Low-Velocity Impact Performance of Biomimetic 3D Printed Engineered Cementitious Composites Beams
  33. An Xuehui, Liang Qimin, Li Pengfei, You Wei et al. (2025-02)
    Experimental Assessment on Printing Performance and Mechanical Properties of Underwater Self-Protecting 3D Printing Concrete
  34. Nan Bo, Qiao Youxin, Leng Junjie, Bai Yikui (2025-01)
    Advancing Structural Reinforcement in 3D Printed Concrete:
    Current Methods, Challenges, and Innovations
  35. Forcael Eric, Medina Moisés, Opazo-Vega Alexander, Moreno Francisco et al. (2024-11)
    Additive Manufacturing in the Construction Industry
  36. Şahin Hatice, Akarsu Özenç Aliye, Saka Dinç Zaide, Mardani Ali et al. (2024-11)
    Investigation of Fresh and Hardened Properties of 3D Printable Concrete Containing Ozone-Modified Carbon-Fiber
  37. Ge Yali, Yao Jie (2024-11)
    Influence of FA and HPMC on the Fresh Properties and Anisotropy of 3D Printing Engineered Cementitious Composites
  38. Sahoo Pitabash, Gupta Souradeep (2024-11)
    3D Printing with Geopolymer-Stabilized Excavated Earth:
    Enhancement of Printability and Engineering-Performance Through Controlled Retardation
  39. Murali Gunasekaran, Leong Sing (2024-11)
    Waste-Driven Construction:
    A State of the Art Review on the Integration of Waste in 3D Printed Concrete in Recent Researches for Sustainable Development
  40. Liu Bing, Guo Yazhao, Wang Yang, Liu Qizhou et al. (2024-11)
    Study on the Compression Performance of 3D Printing Concrete Permanent Formwork Composite Columns
  41. Sousa Israel, Alessandro Antonella, Mesquita Esequiel, Laflamme Simon et al. (2024-11)
    Comprehensive Review of 3D Printed Cementitious Composites with Carbon Inclusions:
    Current Status and Perspective for Self-Sensing Capabilities
  42. Ding Yao, Ou Xingjian, Qi Hongtuo, Xiong Gang et al. (2024-10)
    Inter-Layer Bonding Performance of 3D Printed Engineered Cementitious Composites:
    Rheological Regulation and Fiber Hybridization
  43. Cai Jianguo, Wang Jingsong, Zhang Qian, Du Caixia et al. (2024-10)
    State of the Art of Mechanical Properties of 3D Printed Concrete
  44. Kamhawi Abdallah, Meibodi Mania (2024-09)
    Techniques and Strategies in Extrusion-Based 3D Concrete Printing of Complex Components to Prevent Premature Failure
  45. Han Kang, Gu Fei, Yang Huashan, Tian Xinchen et al. (2024-09)
    PVA-Fiber-Reinforced Red Mud-Based Geopolymer for 3D Printing:
    Printability, Mechanical Properties and Microanalysis
  46. Tittelboom Kim, Mohan Dhanesh, Šavija Branko, Keita Emmanuel et al. (2024-08)
    On the Micro-and Meso-Structure and Durability of 3D Printed Concrete Elements
  47. Rudziewicz Magdalena, Maroszek Marcin, Setlak (nee Pławecka) Kinga, Góra Mateusz et al. (2024-08)
    Optimization of Foams-Polypropylene Fiber-Reinforced Concrete Mixtures Dedicated for 3D Printing
  48. Tanyildizi Harun, Seloglu Maksut, Coskun Ahmet (2024-08)
    The Effect of Nano-Zinc-Oxide on Freeze-Thaw-Resistance of 3D Printed Geopolymer Mortars
  49. Şahin Hatice, Akgümüş Fatih, Mardani Ali (2024-08)
    Mechanical and Rheological Properties of Fiber‐Reinforced 3D Printable Concrete in Terms of Fiber Content and Aspect Ratio
  50. Alonso-Cañon Sara, Blanco-Fernandez Elena, Castro-Fresno Daniel, Yoris-Nobile Adrian et al. (2024-08)
    Comparison of Reinforcement-Fibers in 3D Printing Mortars Using Multi-Criteria Analysis
  51. Xu Wen, Jiang Dengjie, Zhao Qian, Wang Linbing (2024-08)
    Study on Printability of 3D Printing Carbon-Fiber-Reinforced Eco-Friendly Concrete:
    Characterized by Fluidity and Consistency
  52. Srinivas Dodda, Ventrapragada Durga, Panda Biranchi, Sitharam Thallak (2024-07)
    A Study on the Effect of Mixture Constituents on Washout-Resistance, Mechanical, and Transport Properties in the Context of Underwater 3D Concrete Printing
  53. Barve Prasad, Bahrami Alireza, Shah Santosh (2024-07)
    A Comprehensive Review on Effects of Material-Composition, Mix-Design, and Mixing-Regimes on Rheology of 3D Printed Geopolymer Concrete
  54. Shao Lijing, Liu Zhaolong, Liu Qi, Wang Haochuan et al. (2024-07)
    A New Strategy to Enhance 3D Printability of Cement-Based Materials:
    In-Situ Polymerization
  55. Sariyev Bakytzhan, Konysbekov Alisher, Jexembayeva Assel, Konkanov Marat (2024-07)
    A Comparative Study of the Rheological Properties of a Fly-Ash-Based Geopolymer Reinforced with PP-Fiber for 3D Printing:
    An Experimental and Numerical Approach
  56. Ghaffar Seyed, Noaimat Yazeed, Chougan Mehdi, Kheetan Mazen (2024-06)
    Emerging Resources for the Development of Low-Carbon Cementitious Composites for 3D Printing Applications
  57. Krishna R., Rehman Asif, Mishra Jyotirmoy, Saha Suman et al. (2024-06)
    Additive Manufacturing of Geopolymer Composites for Sustainable Construction:
    Critical Factors, Advancements, Challenges, and Future Directions
  58. Masoud Laith, Hammoud Ahmad, Mortada Youssef, Masad Eyad (2024-06)
    Rheological, Mechanical, and Microscopic Properties of Polypropylene-Fiber-Reinforced Geopolymer Concrete for Additive Manufacturing
  59. Zhi Peng, Wu Yuching, Bai Meiyan (2024-06)
    Determining the Effect of Geometric and Dynamic Properties of Screws on Fiber-Orientation During FRC 3D Printing Based on Discrete Element Simulation
  60. Luo Surong, Li Wenqiang, Wang Dehui (2024-05)
    Study on Bending Performance of 3D Printed PVA-Fiber-Reinforced Cement-Based Material
  61. Rahman Mahfuzur, Rawat Sanket, Yang Chunhui, Mahil Ahmed et al. (2024-05)
    A Comprehensive Review on Fresh and Rheological Properties of 3D Printable Cementitious Composites
  62. Oulkhir Fatima, Akhrif Iatimad, Jai Mostapha (2024-05)
    3D Concrete Printing Success:
    An Exhaustive Diagnosis and Failure-Modes-Analysis
  63. Zhou Boyu, Zhang Mo, Ma Guowei (2024-05)
    An Experimental Study on 3D Printed Concrete Reinforced with Fibers Recycled from Wind Turbine Blades
  64. Zaid Osama, Ouni Mohamed (2024-04)
    Advancements in 3D Printing of Cementitious Materials:
    A Review of Mineral Additives, Properties, and Systematic Developments
  65. Tripathi Avinaya, Nair Sooraj, Chauhan Harshitsinh, Neithalath Narayanan (2024-04)
    Print Geometry Alterations and Layer-Staggering to Enhance Mechanical Properties of Plain and Fiber-Reinforced Three-Dimensional-Printed Concrete
  66. Souza Eduarda, Ribeiro Borges Paulo, Stengel Thorsten, Nematollahi Behzad et al. (2024-03)
    3D Printed Sustainable Low-Cost Materials for Construction of Affordable Social Housing in Brazil:
    Potential, Challenges, and Research Needs
  67. Chen Zhengyuan, Yang Shutong, Liu Qi, Xu Mingqi et al. (2024-03)
    Closed-Form Fracture-Model for Evaluating Crack-Resistance of 3D Printed Fiber-Reinforced Alkali-Activated Slag/Fly-Ash Recycled-Sand Concrete
  68. Xiao Jianzhuang, Liu Haoran, Ding Tao, Yu Kequan et al. (2024-02)
    Rebar-Free Concrete Construction:
    Concept, Opportunities and Challenges
  69. Wang Xiaonan, Li Wengui, Guo Yipu, Kashani Alireza et al. (2024-02)
    Concrete 3D Printing Technology in Sustainable Construction:
    A Review on Raw Materials, Concrete Types and Performances
  70. Moraes Maria, Nagata Ester, Duran Afonso, Rossignolo João (2024-02)
    Alkali-Activated Materials Applied in 3D Printing Construction:
    A Review
  71. Zhou Wen, Zhu He, Hu Wei-Hsiu, Wollaston Ryan et al. (2024-02)
    Low-Carbon, Expansive Engineered Cementitious Composites (ECC) In the Context of 3D Printing
  72. Nguyen Vuong, Tran Jonathan, Liu Junli, Tran Mien et al. (2024-02)
    Extended Finite Element Multi-Scale Modelling for Crack Propagation in 3D Printed Fiber-Reinforced Concrete
  73. Li Weihong, Chen Xuhao, Wang Yaoyu, Wan Detian et al. (2024-02)
    Effect of Embedded Filament Fibers on Mechanical Properties of 3D Printing Cement-Based Materials
  74. Fasihi Ali, Libre Nicolas (2024-01)
    From Pumping to Deposition:
    A Comprehensive Review of Test-Methods for Characterizing Concrete-Printability
  75. Pavlin Majda, Horvat Barbara, Cerc Korošec Romana, Capuder Rok et al. (2024-01)
    Characterisation of a 3D Printed Alkali-Activated Material Based on Waste-Mineral-Wool at Room and Elevated Temperatures
  76. Xiao Jianzhuang, Bai Meiyan, Wu Yuching, Duan Zhenhua et al. (2024-01)
    Inter-Layer Bonding Strength and Pore Characteristics of 3D Printed Engineered Cementitious Composites
  77. Fahim Abdullah, Admassu Natnael, Dailey Garret, Moradllo Mehdi (2023-12)
    Application of Cellulose-Nano-Crystals in 3D Printed Alkali-Activated Cementitious Composites
  78. Liu Ke, Takasu Koji, Jiang Jinming, Zu Kun et al. (2023-12)
    Mechanical Properties of 3D Printed Concrete Components:
    A Review
  79. Warsi Syed, Panda Biranchi, Biswas Pankaj (2023-12)
    Exploring Fiber Addition Methods and Mechanical Properties of Fiber-Reinforced 3D Printed Concrete:
    A Review
  80. Nair Sooraj, Tripathi Avinaya, Neithalath Narayanan (2023-11)
    Constitutive Response and Failure Progression in Digitally Fabricated 3D Printed Concrete Under Compression and Their Dependence on Print Layer-Height
  81. Zhi Peng, Wu Yuching, Rabczuk Timon (2023-11)
    Effects of Time-Varying Liquid Bridge Forces on Rheological Properties, and Resulting Extrudability and Constructability of Three-Dimensional Printing Mortar
  82. Ye Junhong, Zhang Jiangdi, Yu Jie, Yu Jiangtao et al. (2023-11)
    Flexural Behaviors of 3D Printed Lightweight Engineered Cementitious Composites (ECC) Slab with Hollow Sections
  83. Zhou Yi, Althoey Fadi, Alotaibi Badr, Gamil Yaser et al. (2023-10)
    An Overview of Recent Advancements in Fiber-Reinforced 3D Printing Concrete
  84. Genc Gokhan, Demircan Ruya, Beyhan Figen, Kaplan Gökhan (2023-10)
    Assessment of the Sustainability and Producibility of Adobe-Constructions Reinforced with Ca-Based Binders:
    Environmental Life-Cycle-Analysis and 3D Printability
  85. Şahin Hatice, Mardani Ali (2023-10)
    How Does Rheological Behavior Affect the Inter-Layer Bonding Strength of 3DPC Mixtures?
  86. Li Leo, Xiao Bofeng, Cheng Cong-Mi, Xie Hui-Zhu et al. (2023-09)
    Adding Glass-Fibers to 3D Printable Mortar:
    Effects on Printability and Material-Anisotropy
  87. Fernández Fernando, Jarabo Rocío, Asensio Eloy, Guerrero Ana (2023-09)
    Non-Destructive Tests to Evaluate the Self-Healing Capacity for a 3D Printing ECC Material
  88. Paritala Spandana, Singaram Kailash, Bathina Indira, Khan Mohd et al. (2023-08)
    Rheology and Pumpability of Mix Suitable for Extrusion-Based Concrete 3D Printing:
    A Review
  89. Zhou Wen, McGee Wesley, Gökçe H., Li Victor (2023-08)
    A Bio-Inspired Solution to Alleviate Anisotropy of 3D Printed Engineered Cementitious Composites (3DP-ECC):
    Knitting/Tilting Filaments
  90. Surehali Sahil, Tripathi Avinaya, Neithalath Narayanan (2023-08)
    Anisotropy in Additively Manufactured Concrete Specimens Under Compressive Loading:
    Quantification of the Effects of Layer-Height and Fiber-Reinforcement
  91. Zhang Yi, Zhu Yanmei, Ren Qiang, He Bei et al. (2023-08)
    Comparison of Printability and Mechanical Properties of Rigid and Flexible Fiber-Reinforced 3D Printed Cement-Based Materials
  92. Jaji Mustapha, Zijl Gideon, Babafemi Adewumi (2023-08)
    Slag-Modified Fiber-Reinforced Metakaolin-Based Geopolymer for 3D Concrete Printing Application:
    Evaluating Fresh and Hardened Properties
  93. Du Longyu, Zhou Jiehang, Lai Jianzhong, Wu Kai et al. (2023-07)
    Effect of Pore-Structure on Durability and Mechanical Performance of 3D Printed Concrete
  94. Pessoa Ana Sofia, Jesus Manuel, Guimarães Ana, Lucas Sandra et al. (2023-07)
    Experimental Characterisation of Hygrothermal Properties of a 3D Printed Cementitious Mortar
  95. Mollah Md., Comminal Raphaël, Silva Wilson, Šeta Berin et al. (2023-07)
    Computational Fluid Dynamics Modelling and Experimental Analysis of Reinforcement-Bar-Integration in 3D Concrete Printing
  96. Tu Haidong, Wei Zhenyun, Bahrami Alireza, Kahla Nabil et al. (2023-06)
    Recent Advancements and Future Trends in 3D Printing Concrete Using Waste-Materials
  97. Riaz Raja, Usman Muhammad, Ali Ammar, Majid Usama et al. (2023-06)
    Inclusive Characterization of 3D Printed Concrete in Additive Manufacturing:
    A Detailed Review
  98. Jesus Manuel, Pessoa Ana Sofia, Guimarães Ana, Rangel Bárbara et al. (2023-06)
    A Reflection on Sustainable Opportunities for 3D Printing in Construction
  99. Chen Wei, Pan Jinlong, Zhu Binrong, Ma XiaoMeng et al. (2023-06)
    Improving Mechanical Properties of 3D Printable One-Part Geopolymer Concrete with Steel-Fiber-Reinforcement
  100. Haar Bjorn, Kruger Jacques, Zijl Gideon (2023-05)
    Off-Site Construction with 3D Concrete Printing
  101. Bhushan Jindal Bharat, Jangra Parveen (2023-05)
    3D Printed Concrete:
    A Comprehensive Review of Raw Material’s Properties, Synthesis, Performance, and Potential Field Applications
  102. Razzaghian Ghadikolaee Mehrdad, Cerro-Prada Elena, Pan Zhu, Korayem Asghar (2023-04)
    Nanomaterials as Promising Additives for High-Performance 3D Printed Concrete:
    A Critical Review
  103. Khan Shoukat, Jassim Muhammad, İlcan Hüseyin, Şahin Oğuzhan et al. (2023-04)
    3D Printing of Circular Materials:
    Comparative Environmental Analysis of Materials and Construction Techniques
  104. Cruz Gil, Dizon John, Farzadnia Nima, Zhou Hongyu et al. (2023-04)
    Performance, Applications, and Sustainability of 3D Printed Cement and Other Geomaterials
  105. Ramezani Amir, Modaresi Shahriar, Dashti Pooria, Givkashi Mohammad et al. (2023-04)
    Effects of Different Types of Fibers on Fresh and Hardened Properties of Cement and Geopolymer-Based 3D Printed Mixtures:
    A Review
  106. Kazemian Ali, Seylabi Elnaz, Ekenel Mahmut (2023-03)
    Concrete 3D Printing:
    Challenges and Opportunities for the Construction Industry
  107. Quah Tan, Tay Yi, Lim Jian, Tan Ming et al. (2023-03)
    Concrete 3D Printing:
    Process-Parameters for Process-Control, Monitoring and Diagnosis in Automation and Construction
  108. Ibrahim Kamoru, Zijl Gideon, Babafemi Adewumi (2023-03)
    Influence of Limestone-Calcined-Clay-Cement on Properties of 3D Printed Concrete for Sustainable Construction
  109. Kaushik Sandipan, Sonebi Mohammed, Amato Giuseppina, Das Utpal et al. (2023-02)
    Optimization of Mix Proportion of 3D Printable Mortar Based on Rheological Properties and Material-Strength Using Factorial Design of Experiment
  110. Şahin Hatice, Mardani Ali (2023-02)
    Mechanical Properties, Durability Performance and Inter-Layer Adhesion of 3DPC Mixtures:
    A State‐of‐the‐art Review
  111. Baigarina Akerke, Shehab Essam, Ali Md. (2023-02)
    Construction 3D Printing:
    A Critical Review and Future Research-Directions
  112. Ahmed Ghafur (2023-01)
    A Review of 3D Concrete Printing:
    Materials and Process Characterization, Economic Considerations and Environmental Sustainability
  113. Zhu Lingli, Yao Jie, Zhao Yu, Ruan Wenqiang et al. (2022-12)
    Effects of Composite Cementation System on Rheological and Working Performances of Fresh 3D Printable Engineered Cementitious Composites
  114. Volpe Stelladriana, Sangiorgio Valentino, Fiorito Francesco, Varum Humberto (2022-12)
    Overview of 3D Construction Printing and Future Perspectives:
    A Review of Technology, Companies and Research Progression
  115. Zhou Yiyi, Jiang Dan, Sharma Rahul, Xie Yi et al. (2022-11)
    Enhancement of 3D Printed Cementitious Composite by Short Fibers:
    A Review
  116. Arunothayan Arun, Nematollahi Behzad, Khayat Kamal, Ramesh Akilesh et al. (2022-11)
    Rheological Characterization of Ultra-High-Performance Concrete for 3D Printing
  117. Lv Chun, Shen Hongtao, Liu Jie, Wu Dan et al. (2022-11)
    Properties of 3D Printing Fiber-Reinforced Geopolymers Based on Inter-Layer Bonding and Anisotropy
  118. Alonso-Cañon Sara, Blanco-Fernandez Elena, Castro-Fresno Daniel, Yoris-Nobile Adrian et al. (2022-11)
    Reinforcements in 3D Printing Concrete Structures
  119. Salaimanimagudam M., Jayaprakash Jaganathan (2022-11)
    Optimum Selection of Reinforcement, Assembly, and Formwork System for Digital Fabrication Technique in Construction Industry:
    A Critical Review
  120. Nguyen Vuong, Liu Junli, Li Shuai, Zhang Guomin et al. (2022-10)
    Modelling of 3D Printed Bio-Inspired Bouligand Cementitious Structures Reinforced with Steel-Fibers
  121. Demiral Nazim, Ozkan Ekinci Mehmet, Şahin Oğuzhan, İlcan Hüseyin et al. (2022-10)
    Mechanical Anisotropy Evaluation and Bonding Properties of 3D Printable Construction and Demolition Waste-Based Geopolymer Mortars
  122. Qaidi Shaker, Yahia Ammar, Tayeh B., Unis H. et al. (2022-10)
    3D Printed Geopolymer Composites:
    A Review
  123. Liu Bing, Liu Xiaoyan, Li Guangtao, Geng Songyuan et al. (2022-09)
    Study on Anisotropy of 3D Printing PVA-Fiber-Reinforced Concrete Using Destructive and Non-Destructive Testing Methods
  124. Chougan Mehdi, Ghaffar Seyed, Nematollahi Behzad, Sikora Paweł et al. (2022-09)
    Effect of Natural and Calcined-Halloysite-Clay-Minerals as Low-Cost-Additives on the Performance of 3D Printed Alkali-Activated Materials
  125. Medicis Carolina, Gonzalez Sergio, Alvarado Yezid, Vacca Hermes et al. (2022-09)
    Mechanical Performance of Commercially Available Premix UHPC-Based 3D Printable Concrete
  126. Ma Lei, Zhang Qing, Lombois-Burger Hélène, Jia Zijian et al. (2022-09)
    Pore-Structure, Internal Relative Humidity, and Fiber-Orientation of 3D Printed Concrete with Polypropylene-Fiber and Their Relation with Shrinkage
  127. Kaliyavaradhan Senthil, Ambily Parukutty, Prem Prabhat, Ghodke Swapnil (2022-08)
    Test-Methods for 3D Printable Concrete
  128. Zhang Yu, Zhang Yunsheng, Yang Lin, Liu Guojian et al. (2022-08)
    Evaluation of Aggregates, Fibers and Voids-Distribution in 3D Printed Concrete
  129. Khosravani Mohammad, Haghighi Azadeh (2022-08)
    Large-Scale Automated Additive Construction:
    Overview, Robotic Solutions, Sustainability, and Future Prospect
  130. Raza Muhammad, Zhong Ray (2022-08)
    A Sustainable Roadmap for Additive Manufacturing Using Geopolymers in Construction Industry
  131. Ahmed Ghafur, Askandar Nasih, Jumaa Ghazi (2022-07)
    A Review of Large-Scale 3DCP:
    Material-Characteristics, Mix-Design, Printing-Process, and Reinforcement-Strategies
  132. Bong Shin, Nematollahi Behzad, Nerella Venkatesh, Mechtcherine Viktor (2022-06)
    Properties of 3D Printable Ductile Fiber-Reinforced Geopolymer Composite
  133. Moelich Gerrit, Kruger Jacques, Combrinck Riaan (2022-06)
    Mitigating Early-Age Cracking in 3D Printed Concrete Using Fibers, Superabsorbent Polymers, Shrinkage Reducing Admixtures, B-CSA Cement and Curing Measures
  134. Christen Heidi, Zijl Gideon, Villiers Wibke (2022-05)
    The Incorporation of Recycled Brick-Aggregate in 3D Printed Concrete
  135. Yang Rijiao, Zeng Qiang, Peng Yu, Wang Hailong et al. (2022-05)
    Anomalous Matrix and Inter-Layer Pore-Structure of 3D Printed Fiber-Reinforced Cementitious Composites
  136. Skibicki Szymon, Pułtorak Monika, Kaszyńska Maria, Hoffmann Marcin et al. (2022-04)
    The Effect of Using Recycled PET-Aggregates on Mechanical and Durability Properties of 3D Printed Mortar
  137. Nodehi Mehrab, Ozbakkaloglu Togay, Gholampour Aliakbar (2022-04)
    Effect of Supplementary Cementitious Materials on Properties of 3D Printed Conventional and Alkali-Activated Concrete:
    A Review
  138. Marchment Taylor, Sanjayan Jay (2022-04)
    Lap Joint Reinforcement for 3D Concrete Printing
  139. Bong Shin, Nematollahi Behzad, Xia Ming, Ghaffar Seyed et al. (2022-04)
    Properties of Additively Manufactured Geopolymer Incorporating Mineral-Wollastonite-Micro-Fibers
  140. Liu Jie, Lv Chun (2022-03)
    Properties of 3D Printed Polymer Fiber-Reinforced Mortars:
    A Review
  141. İlcan Hüseyin, Şahin Oğuzhan, Kul Anil, Yıldırım Gürkan et al. (2022-03)
    Rheological Properties and Compressive Strength of Construction and Demolition Waste-Based Geopolymer Mortars for 3D Printing
  142. Heever Marchant, Plessis Anton, Bester Frederick, Kruger Jacques et al. (2022-02)
    A Mechanistic Evaluation Relating Microstructural Morphology to a Modified Mohr-Griffith Compression-Shear Constitutive-Model for 3D Printed Concrete
  143. Liu Junli, Nguyen Vuong, Panda Biranchi, Fox Kate et al. (2022-02)
    Additive Manufacturing of Sustainable Construction Materials and Form-Finding Structures:
    A Review on Recent Progresses
  144. Heever Marchant, Plessis Anton, Kruger Jacques, Zijl Gideon (2022-01)
    Evaluating the Effects of Porosity on the Mechanical Properties of Extrusion-Based 3D Printed Concrete
  145. Amran Mugahed, Abdelgader Hakim, Onaizi Ali, Fediuk Roman et al. (2021-12)
    3D Printable Alkali-Activated Concretes for Building Applications:
    A Critical Review
  146. Skibicki Szymon, Techman Mateusz, Federowicz Karol, Olczyk Norbert et al. (2021-12)
    Experimental Study of Hardened Young's Modulus for 3D Printed Mortar
  147. Nair Sooraj, Li Anling, Mobasher Barzin, Neithalath Narayanan (2021-12)
    Effect of Layer-Height on Tensile Stress-Distribution and Crack-Width and Propagation in 3D Printed Fiber-Reinforced Flexural Elements
  148. Han Xiaoyu, Yan Jiachuan, Liu Mingjian, Huo Liang et al. (2021-10)
    Experimental Study on Large-Scale 3D Printed Concrete Walls Under Axial Compression
  149. Abudawaba Fareh, Gomaa Eslam, Gheni Ahmed, Gawady Mohamed (2021-09)
    Developing Mix Proportions for Class C Fly-Ash-Based Alkali-Activated 3D Printed Concrete Mixtures
  150. Putten Jolien, Rahul Attupurathu, Schutter Geert, Tittelboom Kim (2021-08)
    Development of 3D Printable Cementitious Composites with the Incorporation of Polypropylene Fibers
  151. Lv Xuesen, Qin Yao, Liang Hang, Cui Xuemin (2021-07)
    Effects of Modifying-Agent on Rheology and Workability of Alkali-Activated Slag-Paste for 3D Extrusion-Forming
  152. Heever Marchant, Bester Frederick, Kruger Jacques, Zijl Gideon (2021-07)
    Mechanical Characterisation for Numerical Simulation of Extrusion-Based 3D Concrete Printing
  153. Bhattacherjee Shantanu, Basavaraj Anusha, Rahul Attupurathu, Santhanam Manu et al. (2021-06)
    Sustainable Materials for 3D Concrete Printing
  154. Suntharalingam Thadshajini, Gatheeshgar Perampalam, Upasiri Irindu, Poologanathan Keerthan et al. (2021-06)
    Fire Performance of Innovative 3D Printed Concrete Composite Wall Panels:
    A Numerical Study
  155. Şahin Oğuzhan, İlcan Hüseyin, Ateşli Anıl, Kul Anil et al. (2021-05)
    Construction and Demolition Waste-Based Geopolymers Suited for Use in 3D Additive Manufacturing
  156. Chung Jihoon, Lee Ghang, Kim Jung-Hoon (2021-04)
    Framework for Technical Specifications of 3D Concrete Printers
  157. Zhang Hao, Zhu Liming, Zhang Fan, Yang Mijia (2021-04)
    Effect of Fiber Content and Alignment on the Mechanical Properties of 3D Printing Cementitious Composites
  158. Bong Shin, Xia Ming, Nematollahi Behzad, Shi Caijun (2021-04)
    Ambient Temperature Cured ‘Just-Add-Water’ Geopolymer for 3D Concrete Printing Applications
  159. Zhu Binrong, Nematollahi Behzad, Pan Jinlong, Zhang Yang et al. (2021-04)
    3D Concrete Printing of Permanent Formwork for Concrete Column Construction
  160. Yu Kequan, McGee Wesley, Ng Tsz, Zhu He et al. (2021-02)
    3D Printable Engineered Cementitious Composites:
    Fresh and Hardened Properties
  161. Ye Junhong, Cui Can, Yu Jiangtao, Yu Kequan et al. (2021-02)
    Effect of Polyethylene-Fiber Content on Workability and Mechanical-Anisotropic Properties of 3D Printed Ultra-High-Ductile Concrete
  162. Arunothayan Arun, Nematollahi Behzad, Ranade Ravi, Bong Shin et al. (2021-02)
    Fiber-Orientation Effects on Ultra-High-Performance Concrete Formed by 3D Printing
  163. Chougan Mehdi, Ghaffar Seyed, Sikora Paweł, Chung Sang-Yeop et al. (2021-02)
    Investigation of Additive Incorporation on Rheological, Microstructural and Mechanical Properties of 3D Printable Alkali-Activated Materials
  164. Mechtcherine Viktor, Buswell Richard, Kloft Harald, Bos Freek et al. (2021-02)
    Integrating Reinforcement in Digital Fabrication with Concrete:
    A Review and Classification Framework
  165. Ye Junhong, Cui Can, Yu Jiangtao, Yu Kequan et al. (2021-01)
    Fresh and Anisotropic-Mechanical Properties of 3D Printable Ultra-High-Ductile Concrete with Crumb-Rubber
  166. Kristombu Baduge Shanaka, Navaratnam Satheeskumar, Zidan Yousef, McCormack Tom et al. (2021-01)
    Improving Performance of Additive Manufactured Concrete:
    A Review on Material Mix-Design, Processing, Inter-Layer Bonding, and Reinforcing-Methods
  167. Skibicki Szymon, Pułtorak Monika, Kaszyńska Maria (2021-01)
    Evaluation of Material-Modification Using PET in 3D Concrete Printing Technology
  168. Luhar Salmabanu, Suntharalingam Thadshajini, Navaratnam Satheeskumar, Luhar Ismail et al. (2020-12)
    Sustainable and Renewable Bio-Based Natural Fibers and Its Application for 3D Printed Concrete:
    A Review
  169. Sun Xiaoyan, Gao Chao, Wang Hailong (2020-10)
    Bond-Performance Between BFRP-Bars and 3D Printed Concrete
  170. Mohan Manu, Rahul Attupurathu, Schutter Geert, Tittelboom Kim (2020-10)
    Extrusion-Based Concrete 3D Printing from a Material Perspective:
    A State of the Art Review
  171. Alchaar Aktham, Tamimi Adil (2020-10)
    Mechanical Properties of 3D Printed Concrete in Hot Temperatures
  172. Arunothayan Arun, Nematollahi Behzad, Ranade Ravi, Bong Shin et al. (2020-10)
    Development of 3D Printable Ultra-High-Performance Fiber-Reinforced Concrete for Digital Construction
  173. Kruger Jacques, Zijl Gideon (2020-10)
    A Compendious Review on Lack-of-Fusion in Digital Concrete Fabrication
  174. Chu Shaohua, Li Leo, Kwan Albert (2020-09)
    Development of Extrudable High-Strength Fiber-Reinforced Concrete Incorporating Nano-Calcium-Carbonate
  175. Marchment Taylor, Sanjayan Jay (2020-09)
    Bond Properties of Reinforcing Bar Penetrations in 3D Concrete Printing
  176. Ding Tao, Xiao Jianzhuang, Zou Shuai, Zhou Xinji (2020-08)
    Anisotropic Behavior in Bending of 3D Printed Concrete Reinforced with Fibers
  177. Nematollahi Behzad, Bong Shin, Xia Ming, Sanjayan Jay (2020-07)
    Digital Fabrication of ‘Just-Add-Water’ Geopolymers:
    Effects of Curing Condition and Print-Time Interval
  178. Suntharalingam Thadshajini, Nagaratnam Brabha, Poologanathan Keerthan, Hackney Phil et al. (2020-07)
    Effect of Polypropylene-Fibers on the Mechanical Properties of Extrudable Cementitious Material
  179. Shahzad Qamar, Wang Xujiang, Wang Wenlong, Wan Yi et al. (2020-06)
    Coordinated Adjustment and Optimization of Setting-Time, Flowability, and Mechanical Strength for Construction 3D Printing Material Derived from Solid Waste
  180. Muthukrishnan Shravan, Kua Harn, Yu Ling, Chung Jacky (2020-05)
    Fresh Properties of Cementitious Materials Containing Rice-Husk-Ash for Construction 3D Printing
  181. Assaad Joseph, Yassin Abdallah, Sakka Fatima, Hamzeh Farook (2020-05)
    A Modular Approach for Steel Reinforcing of 3D Printed Concrete:
    Preliminary Study
  182. Figueiredo Stefan, Rodríguez Claudia, Ahmed Zeeshan, Bos Derk et al. (2020-05)
    Mechanical Behavior of Printed Strain-Hardening Cementitious Composites
  183. Khan Mohammad, Sanchez Florence, Zhou Hongyu (2020-04)
    3D Printing of Concrete:
    Beyond Horizons
  184. Li Victor, Bos Freek, Yu Kequan, McGee Wesley et al. (2020-04)
    On the Emergence of 3D Printable Engineered, Strain-Hardening Cementitious Composites
  185. Chougan Mehdi, Ghaffar Seyed, Jahanzat Mohammad, Albar Abdulrahman et al. (2020-04)
    The Influence of Nano-Additives in Strengthening Mechanical Performance of 3D Printed Multi-Binder Geopolymer Composites
  186. Kosson Michael, Brown Lesa, Sanchez Florence (2020-01)
    Early-Age Performance of 3D Printed Carbon-Nano-Fiber and Carbon Micro-Fiber Cement Composites
  187. Baz Bilal, Aouad Georges, Rémond Sébastien (2020-01)
    Effect of the Printing Method and Mortar’s Workability on Pull-Out Strength of 3D Printed Elements
  188. Siddika Ayesha, Mamun Md., Ferdous Wahid, Saha Ashish et al. (2019-12)
    3D Printed Concrete:
    Applications, Performance, and Challenges
  189. Suntharalingam Thadshajini, Nagaratnam Brabha, Poologanathan Keerthan, Hackney Phil et al. (2019-12)
    Effect of Polypropylene-Fibers on the Workability Parameters of Extrudable Cementitious Materials
  190. Markin Slava, Šahmenko Genādijs, Nerella Venkatesh, Näther Mathias et al. (2019-11)
    Investigations on the Foam-Concrete Production Techniques Suitable for 3D Printing with Foam-Concrete
  191. Marchment Taylor, Sanjayan Jay (2019-10)
    Mesh Reinforcing Method for 3D Concrete Printing
  192. Arunothayan Arun, Nematollahi Behzad, Bong Shin, Ranade Ravi et al. (2019-09)
    Hardened Properties of 3D Printable Ultra-High-Performance Fiber-Reinforced Concrete for Digital Construction Applications
  193. Bong Shin, Nematollahi Behzad, Xia Ming, Nazari Ali et al. (2019-09)
    Properties of 3D Printable Ductile Fiber-Reinforced Geopolymer Composite for Digital Construction Applications
  194. Nematollahi Behzad, Xia Ming, Sanjayan Jay (2019-09)
    Enhancing Strength of Powder-Based 3D Printed Geopolymers for Digital Construction Applications
  195. Panda Biranchi, Unluer Cise, Tan Ming (2019-08)
    Extrusion and Rheology Characterization of Geopolymer Nanocomposites Used in 3D Printing
  196. Zhu Binrong, Pan Jinlong, Nematollahi Behzad, Zhou Zhenxin et al. (2019-07)
    Development of 3D Printable Engineered Cementitious Composites with Ultra-High Tensile Ductility for Digital Construction
  197. Kruger Jacques, Zeranka Stephan, Zijl Gideon (2019-07)
    An Ab-Inito Approach for Thixotropy Characterisation of Nano-Particle-Infused 3D Printable Concrete
  198. Wangler Timothy, Roussel Nicolas, Bos Freek, Salet Theo et al. (2019-06)
    Digital Concrete:
    A Review
  199. Nematollahi Behzad, Xia Ming, Vijay Praful, Sanjayan Jay (2019-02)
    Properties of Extrusion-Based 3D Printable Geopolymers for Digital Construction Applications

BibTeX 
@article{nema_vija_sanj_naza.2018.EoPFAoPoGMb3PfDC,
  author            = "Behzad Nematollahi and Praful Vijay and Jay Gnananandan Sanjayan and Ali Nazari and Ming Xia and Venkatesh Naidu Nerella and Viktor Mechtcherine",
  title             = "Effect of Polypropylene Fiber Addition on Properties of Geopolymers Made by 3D Printing for Digital Construction",
  doi               = "10.3390/ma11122352",
  year              = "2018",
  journal           = "Materials",
  volume            = "11",
  number            = "12",
}
Formatted Citation

B. Nematollahi, “Effect of Polypropylene Fiber Addition on Properties of Geopolymers Made by 3D Printing for Digital Construction”, Materials, vol. 11, no. 12, 2018, doi: 10.3390/ma11122352.

Nematollahi, Behzad, Praful Vijay, Jay Gnananandan Sanjayan, Ali Nazari, Ming Xia, Venkatesh Naidu Nerella, and Viktor Mechtcherine. “Effect of Polypropylene Fiber Addition on Properties of Geopolymers Made by 3D Printing for Digital Construction”. Materials 11, no. 12 (2018). https://doi.org/10.3390/ma11122352.