Tan Ming¶

1. Jhun Jihye, Lee Junghyun, Paul Suvash, Lim Sean et al. (2026-01)
   Potential of Rice Husk Biochar in 3D Concrete Printing:
   An Analysis of Fresh-State Rheology, Strength Retention, and Carbon Sequestration
2. Wang Xiangyu, Wang Sizhe, Deng North, Liu Zhenbang et al. (2026-01)
   Robotic Rebar Insertion and Grouting for Reinforcement of 3D Printed Concrete:
   Technique Development and Bond Behavior Characterization
3. Liu Zhenbang, Li Mingyang, Wang Sizhe, Deng North et al. (2026-01)
   Investigation on Bond-Slip Performance of Steel Rebar Embedded in Concrete Confined by 3D Concrete Printing Formwork
4. Paul Suvash, Lee Junghyun, Tay Yi, Amr Issam et al. (2025-12)
   Developing Sustainable 3D Printable Concrete Materials Using Olivine Sand for Carbon Sequestration
5. Deng North, Wang Sizhe, Li Mingyang, Wang Xiangyu et al. (2025-12)
   A Perforated Strip-Based Three-Dimensional Reinforcement Strategy for 3D Printed Concrete:
   Flexural Testing of Beams as a Proof of Concept
6. Lim Sean, Lee Junghyun, Bawarith Nuran, Paul Suvash et al. (2025-11)
   The Efficacy of Self-Curing Agents on Enhanced Internal Curing and Accelerated Carbonation with CO2-Steam Integrated 3D Concrete Printing
7. Quah Tan, Liu Zhixin, Tay Yi, Li Mingyang et al. (2025-08)
   In-Process Filament Repair in 3D Concrete Printing with Instance Segmentation
8. Liu Zhenbang, Li Mingyang, Wang Xiangyu, Wong Teck et al. (2025-03)
   Investigate Mechanisms of Different Printing Parameters on the Mechanical Anisotropy of 3D Concrete Printing Elements by Using Computed Tomography Scan and Computational Fluid Dynamics Methods
9. Lim Sean, Tan Ming (2024-10)
   A Rheological Model for Concrete Additive Manufacturing
10. Lim Sean, Tay Yi, Paul Suvash, Lee Junghyun et al. (2024-09)
    Carbon Capture and Sequestration with In-Situ CO2 and Steam Integrated 3D Concrete Printing
11. Wang Xiangyu, Du Liangfen, Liu Zhenbang, Li Mingyang et al. (2024-09)
    3D Cementitious Composites Printing with Pretreated Recycled Crumb-Rubber:
    Mechanical and Acoustic Insulation Properties
12. Ting Guan, Tay Yi, Quah Tan, Tan Ming et al. (2024-09)
    Sustainable Support-Material for Overhang Printing in 3D Concrete Printing Technology
13. Liu Zhenbang, Li Mingyang, Wang Xiangyu, Wang Sizhe et al. (2024-07)
    Axial Performances of the Steel-Rebar-Reinforced Column Confined by the Steel-Cable-Reinforced 3D Concrete Printing Permanent Formwork
14. Geng Zifan, Zhang Lizhi, Wu Zhiwen, Tay Yi et al. (2024-07)
    Mechanical Properties and Additive Manufacturing of Alkali-Activated Lunar Regolith in Artificial Lunar Environments
15. Lim Sean, Tay Yi, Amr Issam, Fadhel Bandar et al. (2024-07)
    Carbon Sequestration with 3D Concrete Printing:
    Potentials and Challenges
16. Quah Tan, Tay Yi, Tan Ming, Li King (2024-07)
    Evaluation of Extrusion-Methods for 3D Concrete Printing
17. Tay Yi, Soh Eugene, Ferrand Hortense, Tan Ming (2024-07)
    3D Printing of Large-Scale Biodegradable Material
18. Tay Yi, Wang Lining, Wang Xiangyu, Quah Tan et al. (2024-07)
    Integration of Functional Materials into 3D Printing for Construction
19. Liu Zhenbang, Li Mingyang, Wong Teck, Tan Ming (2024-05)
    Determine the Effects of Pore Properties on the Mechanical Performances of 3D Concrete Printing Units with Experimental and Numerical Methods
20. Lu Bing, Wang Lining, Wang Xiangyu, Tan Ming et al. (2024-04)
    Development of Robotic Sprayable Self-Sensing Cementitious Material for Smart Structural Health Monitoring
21. Tay Yi, Lim Sean, Phua Seng, Tan Ming et al. (2023-10)
    Exploring Carbon-Sequestration-Potential Through 3D Concrete Printing
22. Liu Zhenbang, Li Mingyang, Quah Tan, Wong Teck et al. (2023-09)
    Comprehensive Investigations on the Relationship Between the 3D Concrete Printing Failure Criterion and Properties of Fresh-State Cementitious Materials
23. Li Mingyang, Zhang Dong, Wong Teck, Tan Ming et al. (2023-09)
    Modeling and Experimental Investigation of Fiber Orientation in Cast and 3D Printed Cementitious Composites
24. Quah Tan, Vo Tran, Tay Yi, Tan Ming et al. (2023-09)
    Real-Time-Assessment of Smart Concrete Inspection with Piezoelectric Sensors
25. Liu Zhenbang, Li Mingyang, Moo Guo, Kobayashi Hitoshi et al. (2023-05)
    Effect of Nano-Structured Silica-Additives on the Extrusion-Based 3D Concrete Printing Application
26. Quah Tan, Tay Yi, Lim Jian, Tan Ming et al. (2023-03)
    Concrete 3D Printing:
    Process-Parameters for Process-Control, Monitoring and Diagnosis in Automation and Construction
27. Tay Yi, Ting Guan, Panda Biranchi, Wong Teck et al. (2022-11)
    Towards Net-Zero in 3DP for Building & Construction
28. Li Mingyang, Zhang Xu, Tay Yi, Ting Guan et al. (2022-07)
    Three-Dimensional (3D) Printing for Building and Construction
29. Tay Yi, Lim Jian, Li Mingyang, Tan Ming (2022-03)
    Creating Functionally Graded Concrete Materials with Varying 3D Printing Parameters
30. Ting Guan, Quah Tan, Lim Jian, Tay Yi et al. (2022-01)
    Extrudable Region Parametrical Study of 3D Printable Concrete Using Recycled-Glass Concrete
31. Ting Guan, Tay Yi, Tan Ming (2021-04)
    Experimental Measurement on the Effects of Recycled Glass-Cullets as Aggregates for Construction 3D Printing
32. Weng Yiwei, Li Mingyang, Zhang Dong, Tan Ming et al. (2021-02)
    Investigation of Inter-Layer Adhesion of 3D Printable Cementitious Material from the Aspect of Printing-Process
33. Weng Yiwei, Mohamed Nisar, Lee Brian, Gan Nicole et al. (2021-02)
    Extracting BIM Information for Lattice Tool-Path-Planning in Digital Concrete Printing with Developed Dynamo Script:
    A Case Study
34. Weng Yiwei, Li Mingyang, Wong Teck, Tan Ming (2021-01)
    Synchronized Concrete and Bonding-Agent-Deposition-System for Inter-Layer Bond Strength Enhancement in 3D Concrete Printing
35. Panda Biranchi, Sonat Cem, Yang En-Hua, Tan Ming et al. (2020-12)
    Use of Magnesium-Silicate-Hydrate (M-S-H) Cement Mixes in 3D Printing Applications
36. Tay Yi, Panda Biranchi, Ting Guan, Ahamed N. et al. (2020-10)
    3D Printing for Sustainable Construction
37. Liu Zhixin, Li Mingyang, Tay Yi, Weng Yiwei et al. (2020-04)
    Rotation-Nozzle and Numerical Simulation of Mass-Distribution at Corners in 3D Cementitious Material-Printing
38. Liu Zhixin, Li Mingyang, Weng Yiwei, Qian Ye et al. (2020-03)
    Modelling- and Parameter-Optimization for Filament-Deformation in 3D Cementitious Material-Printing Using Support-Vector-Machine
39. Weng Yiwei, Li Mingyang, Ruan Shaoqin, Wong Teck et al. (2020-03)
    Comparative Economic, Environmental and Productivity-Assessment of a Concrete Bathroom Unit Fabricated Through 3D Printing and a Pre-Cast Approach
40. Lu Bing, Zhu Weiping, Weng Yiwei, Liu Zhixin et al. (2020-02)
    Study of MgO-Activated-Slag as a Cementless Material for Sustainable Spray-Based 3D Printing
41. Lao Wenxin, Li Mingyang, Wong Teck, Tan Ming et al. (2020-02)
    Improving Surface-Finish-Quality in Extrusion-Based 3D Concrete Printing Using Machine-Learning-Based Extrudate-Geometry-Control
42. Panda Biranchi, Ruan Shaoqin, Unluer Cise, Tan Ming (2020-01)
    Investigation of the Properties of Alkali-Activated Slag Mixes Involving the Use of Nano-Clay and Nucleation-Seeds for 3D Printing
43. Panda Biranchi, Mohamed Nisar, Tan Ming (2019-09)
    Rheology and Structural Rebuilding of One-Part Geopolymer Mortar in the Context of 3D Concrete Printing
44. Panda Biranchi, Unluer Cise, Tan Ming (2019-08)
    Extrusion and Rheology Characterization of Geopolymer Nanocomposites Used in 3D Printing
45. Panda Biranchi, Mohamed Nisar, Paul Suvash, Bhagath Singh Gangapatnam et al. (2019-07)
    The Effect of Material Fresh Properties and Process Parameters on Buildability and Inter-Layer Adhesion of 3D Printed Concrete
46. Weng Yiwei, Ruan Shaoqin, Li Mingyang, Mo Liwu et al. (2019-06)
    Feasibility Study on Sustainable-Magnesium-Potassium-Phosphate Cement-Paste for 3D Printing
47. Tay Yi, Qian Ye, Tan Ming (2019-05)
    Printability-Region for 3D Concrete Printing Using Slump- and Slump-Flow-Test
48. Tay Yi, Li Mingyang, Tan Ming (2019-04)
    Effect of Printing Parameters in 3D Concrete Printing:
    Printing Region and Support Structures
49. Lu Bing, Qian Ye, Li Mingyang, Weng Yiwei et al. (2019-04)
    Designing Spray-Based 3D Printable Cementitious Materials with Fly-Ash-Cenosphere and Air-Entraining Agent
50. Ting Guan, Tay Yi, Qian Ye, Tan Ming (2019-03)
    Utilization of Recycled Glass for 3D Concrete Printing:
    Rheological and Mechanical Properties
51. Lu Bing, Weng Yiwei, Li Mingyang, Qian Ye et al. (2019-02)
    A Systematical Review of 3D Printable Cementitious Materials
52. Weng Yiwei, Li Mingyang, Tan Ming, Qian Shunzhi (2019-02)
    Design 3D Printing Cementitious Materials via Fuller-Thompson-Theory and Marson-Percy-Model
53. Panda Biranchi, Bhagath Singh Gangapatnam, Unluer Cise, Tan Ming (2019-02)
    Synthesis and Characterization of One-Part Geopolymers for Extrusion-Based 3D Concrete Printing
54. Panda Biranchi, Lim Jian, Tan Ming (2019-02)
    Mechanical Properties and Deformation Behavior of Early-Age Concrete in the Context of Digital Construction
55. Weng Yiwei, Li Mingyang, Liu Zhixin, Lao Wenxin et al. (2018-12)
    Printability and Fire Performance of a Developed 3D Printable Fiber-Reinforced Cementitious Composites under Elevated Temperatures
56. Liu Zhixin, Li Mingyang, Weng Yiwei, Wong Teck et al. (2018-12)
    Mixture-Design-Approach to Optimize the Rheological Properties of the Material Used in 3D Cementitious Material-Printing
57. Panda Biranchi, Tan Ming (2018-11)
    Rheological Behavior of High-Volume Fly-Ash Mixtures Containing Micro-Silica for Digital Construction Application
58. Panda Biranchi, Ruan Shaoqin, Unluer Cise, Tan Ming (2018-11)
    Improving the 3D Printability of High-Volume Fly-Ash Mixtures via the Use of Nano-Attapulgite-Clay
59. Panda Biranchi, Unluer Cise, Tan Ming (2018-10)
    Investigation of the Rheology and Strength of Geopolymer Mixtures for Extrusion-Based 3D Printing
60. Weng Yiwei, Lu Bing, Li Mingyang, Liu Zhixin et al. (2018-09)
    Empirical Models to Predict Rheological Properties of Fiber-Reinforced Cementitious Composites for 3D Printing
61. Panda Biranchi, Mohamed Nisar, Tay Yi, Tan Ming (2018-09)
    Bond Strength in 3D Printed Geopolymer Mortar
62. Lu Bing, Li Mingyang, Lao Wenxin, Weng Yiwei et al. (2018-08)
    Experimental Investigation of Printing Parameters on Material-Distribution in 3D Spray Cementitious Material Printing Process
63. Lu Bing, Li Mingyang, Lao Wenxin, Weng Yiwei et al. (2018-08)
    Effect of Spray-Based Printing Parameters on Cementitious Material-Distribution
64. Tay Yi, Ting Guan, Qian Ye, Panda Biranchi et al. (2018-07)
    Time-Gap-Effect on Bond Strength of 3D Printed Concrete
65. Panda Biranchi, Tay Yi, Paul Suvash, Tan Ming (2018-05)
    Current Challenges and Future Potential of 3D Concrete Printing
66. Annapareddy Ashokreddy, Panda Biranchi, Ting Guan, Li Mingyang et al. (2018-05)
    Flow And Mechanical Properties of 3D Printed Cementitious Material With Recycled Glass-Aggregates
67. Lao Wenxin, Tay Yi, Quirin Didier, Tan Ming (2018-05)
    The Effect of Nozzle Shapes on the Compactness and Strength of Structure Printed in Additive Manufacturing of Concrete
68. Li Mingyang, Lao Wenxin, He Lewei, Masia Lorenzo et al. (2018-05)
    Effect of Rotational Trapezoid Shaped Nozzle on Material-Distribution in 3D Cementitious Material-Printing-Process
69. Liu Zhixin, Li Mingyang, Wong Teck, Tan Ming (2018-05)
    Measurement of the Fresh Rheological Properties of Material in 3D Printing
70. Lu Bing, Li Mingyang, Qian Shunzhi, Leong Kah et al. (2018-05)
    Develop Cementitious Materials Incoporating Fly-Ash-Cenophere for Spray-Based 3D Printing
71. Panda Biranchi, Mohamed Nisar, Tay Yi, He Lewei et al. (2018-05)
    Effects Of Slag Addition On Bond Strength Of 3D Printed Geopolymer Mortar:
    An Experimental Investigation
72. Tay Yi, Ting Guan, Panda Biranchi, He Lewei et al. (2018-05)
    Bond Strength of 3D Printed Concrete
73. Ting Andrew, Tay Yi, Annapareddy Ashokreddy, Li Mingyang et al. (2018-05)
    Effect of Recycled-Glass Gradation in 3D Cementitious Material-Printing
74. Weng Yiwei, Qian Shunzhi, He Lewei, Li Mingyang et al. (2018-05)
    3D Printable High-Performance Fiber-Reinforced Cementitious Composites For Large-Scale Printing
75. Paul Suvash, Zijl Gideon, Tan Ming, Gibson Ian (2018-05)
    A Review of 3D Concrete Printing Systems and Materials Properties:
    Current Status and Future Research Prospects
76. Panda Biranchi, Mohamed Nisar, Tan Ming (2018-04)
    Effect of 3D Printing on Mechanical Properties of Fly Ash-Based Inorganic Geopolymer
77. Panda Biranchi, Tan Ming (2018-03)
    Experimental Study on Mix Proportion and Fresh Properties of Fly-Ash-Based Geopolymer for 3D Concrete Printing
78. Weng Yiwei, Li Mingyang, Tan Ming, Qian Shunzhi (2018-01)
    Design 3D Printing Cementitious Materials via Fuller-Thompson-Theory and Marson-Percy-Model
79. Panda Biranchi, Paul Suvash, Mohamed Nisar, Tay Yi et al. (2017-09)
    Measurement of Tensile Bond Strength of 3D Printed Geopolymer Mortar
80. Paul Suvash, Tay Yi, Panda Biranchi, Tan Ming (2017-08)
    Fresh and Hardened Properties of 3D Printable Cementitious Materials for Building and Construction
81. Panda Biranchi, Paul Suvash, Lim Jian, Tay Yi et al. (2017-08)
    Additive Manufacturing of Geopolymer for Sustainable Built Environment
82. Lao Wenxin, Li Mingyang, Masia Lorenzo, Tan Ming (2017-08)
    Approaching Rectangular Extrudate in 3D Printing for Building and Construction by Experimental Iteration of Nozzle Design
83. Panda Biranchi, Paul Suvash, Tan Ming (2017-07)
    Anisotropic Mechanical Performance of 3D Printed Fiber-Reinforced Sustainable Construction-Material
84. Panda Biranchi, Lim Jian, Mohamed Nisar, Paul Suvash et al. (2017-07)
    Automation of Robotic Concrete Printing Using Feedback-Control-System
85. Tay Yi, Panda Biranchi, Paul Suvash, Mohamed Nisar et al. (2017-05)
    3D Printing Trends in Building and Construction Industry:
    A Review