Assessment of the Sustainability and Producibility of Adobe-Constructions Reinforced with Ca-Based Binders (2023-10)¶
10.1016/j.scitotenv.2023.167695
Genc Gokhan, Demircan Ruya, Beyhan Figen,
Journal Article - Science of the Total Environment, No. 167695
Abstract
This study investigated the usability of adobe samples reinforced with calcium-based binders in a 3D-printed technique. These adobe samples' physical, mechanical, durability and microstructure characteristics were investigated and their 3D printability characteristics experimentally. In the case of adobe production by 3D-printing method, the compressive strength decreased by 9–33 % compared to mold casting. While the thermal conductivity coefficient of adobe samples varied between 0.833 and 1.421 W/mK, the thermal conductivity was reduced by 43 % thanks to the preference for gypsum. Within the scope of the LCA analysis, the slightest effect in terms of environmental damage was observed in mixtures containing gypsum compared to cement and slaked lime mixtures. As a result, it was determined that adobe's physical and mechanical characteristics could be improved by using gypsum, lime and cement, and these mixtures can be used in 3D-printing. It was determined that more sustainable adobe production is possible with gypsum and lime.
¶
39 References
- Alhumayani Hashem, Gomaa Mohamed, Soebarto Veronica, Jabi Wassim (2020-06)
Environmental Assessment of Large-Scale 3D Printing in Construction:
A Comparative Study between Cob and Concrete - Alqenaee Amnah, Memari Ali (2022-02)
Experimental Study of 3D Printable Cob Mixtures - Arunothayan Arun, Nematollahi Behzad, Ranade Ravi, Bong Shin et al. (2020-10)
Development of 3D Printable Ultra-High-Performance Fiber-Reinforced Concrete for Digital Construction - Bong Shin, Nematollahi Behzad, Nazari Ali, Xia Ming et al. (2019-03)
Method of Optimization for Ambient Temperature Cured Sustainable Geopolymers for 3D Printing Construction Applications - Chaiyotha Danai, Kantawong Watcharapong, Payakanitia Panjasila, Pinitsoontorn Supree et al. (2023-03)
Finding Optimized Conditions for 3D Printed High-Calcium Fly-Ash-Based Alkali-Activated Mortar - Daher Jana, Kleib Joelle, Benzerzour Mahfoud, Abriak Nor-Edine et al. (2022-09)
Recycling of Flash-Calcined Dredged Sediment for Concrete 3D Printing - Ding Tao, Xiao Jianzhuang, Zou Shuai, Wang Yu (2020-06)
Hardened Properties of Layered 3D Printed Concrete with Recycled Sand - Gao Yanan, Hua Sudong, Yue Hongfei (2023-04)
Study on Preparation and Rheological Properties of 3D Printed Pre-Foaming Concrete - Gomaa Mohamed, Jabi Wassim, Soebarto Veronica, Xie Yi (2022-01)
Digital Manufacturing for Earth Construction:
A Critical Review - Gomaa Mohamed, Jabi Wassim, Veliz-Reyes Alejandro, Soebarto Veronica (2021-01)
3D Printing System for Earth-Based Construction:
Case Study of Cob - Han Yilong, Yang Zhihan, Ding Tao, Xiao Jianzhuang (2020-08)
Environmental and Economic Assessment on 3D Printed Buildings with Recycled Concrete - İlcan Hüseyin, Şahin Oğuzhan, Kul Anil, Yıldırım Gürkan et al. (2022-03)
Rheological Properties and Compressive Strength of Construction and Demolition Waste-Based Geopolymer Mortars for 3D Printing - Jeong Hoseong, Han Sun-Jin, Choi Seung-Ho, Lee Yoon et al. (2019-02)
Rheological Property Criteria for Buildable 3D Printing Concrete - Ji Guangchao, Ding Tao, Xiao Jianzhuang, Du Shupeng et al. (2019-05)
A 3D Printed Ready-Mixed Concrete Power-Distribution Substation:
Materials and Construction Technology - Khalil Noura, Aouad Georges, Cheikh Khadija, Rémond Sébastien (2017-09)
Use of Calcium-Sulfoaluminate-Cements for Setting-Control of 3D Printing Mortars - Khoshnevis Behrokh (2003-11)
Automated Construction by Contour Crafting:
Related Robotics and Information Technologies - Le Thanh, Austin Simon, Lim Sungwoo, Buswell Richard et al. (2012-01)
Hardened Properties of High-Performance Printing Concrete - Ma Guowei, A Ruhan, Xie Panpan, Pan Zhu et al. (2022-01)
3D Printable Aerogel-Incorporated Concrete:
Anisotropy Influence on Physical, Mechanical, and Thermal Insulation Properties - Mo Yixin, Xing Jianchun, Yue Songlin, Zhang Yamei et al. (2022-04)
Dynamic Properties of 3D Printed Cement Mortar Based on Split Hopkinson Pressure Bar Testing - Nematollahi Behzad, Vijay Praful, Sanjayan Jay, Nazari Ali et al. (2018-11)
Effect of Polypropylene Fiber Addition on Properties of Geopolymers Made by 3D Printing for Digital Construction - Nerella Venkatesh, Hempel Simone, Mechtcherine Viktor (2019-02)
Effects of Layer-Interface Properties on Mechanical Performance of Concrete Elements Produced by Extrusion-Based 3D Printing - Ngo Tuan, Kashani Alireza, Imbalzano Gabriele, Nguyen Quynh et al. (2018-02)
Additive Manufacturing (3D Printing):
A Review of Materials, Methods, Applications and Challenges - Panda Biranchi, Paul Suvash, Lim Jian, Tay Yi et al. (2017-08)
Additive Manufacturing of Geopolymer for Sustainable Built Environment - Panda Biranchi, Paul Suvash, Tan Ming (2017-07)
Anisotropic Mechanical Performance of 3D Printed Fiber-Reinforced Sustainable Construction-Material - Pasupathy Kirubajiny, Ramakrishnan Sayanthan, Sanjayan Jay (2022-07)
Enhancing the Properties of Foam-Concrete 3D Printing Using Porous Aggregates - Pasupathy Kirubajiny, Ramakrishnan Sayanthan, Sanjayan Jay (2023-01)
3D Concrete Printing of Eco-Friendly Geopolymer Containing Brick Waste - Pegna Joseph (1997-02)
Exploratory Investigation of Solid Freeform Construction - Ramakrishnan Sayanthan, Muthukrishnan Shravan, Sanjayan Jay, Pasupathy Kirubajiny (2021-08)
Concrete 3D Printing of Lightweight Elements Using Hollow-Core Extrusion of Filaments - Sanjayan Jay, Nematollahi Behzad, Xia Ming, Marchment Taylor (2018-04)
Effect of Surface Moisture on Inter-Layer Strength of 3D Printed Concrete - Schutter Geert, Lesage Karel, Mechtcherine Viktor, Nerella Venkatesh et al. (2018-08)
Vision of 3D Printing with Concrete:
Technical, Economic and Environmental Potentials - Shakor Pshtiwan, Sanjayan Jay, Nazari Ali, Nejadi Shami (2017-02)
Modified 3D Printed Powder to Cement-Based Material and Mechanical Properties of Cement Scaffold Used in 3D Printing - Souza Marcelo, Ferreira Igor, Moraes Elisângela, Senff Luciano et al. (2020-09)
3D Printed Concrete for Large-Scale Buildings:
An Overview of Rheology, Printing Parameters, Chemical Admixtures, Reinforcements, and Economic and Environmental Prospects - Tay Yi, Qian Ye, Tan Ming (2019-05)
Printability-Region for 3D Concrete Printing Using Slump- and Slump-Flow-Test - Ting Guan, Tay Yi, Tan Ming (2021-04)
Experimental Measurement on the Effects of Recycled Glass-Cullets as Aggregates for Construction 3D Printing - Wang Li, Ma Guowei, Liu Tianhao, Buswell Richard et al. (2021-07)
Inter-Layer Reinforcement of 3D Printed Concrete by the In-Process Deposition of U-Nails - Wolfs Robert, Bos Freek, Salet Theo (2019-03)
Hardened Properties of 3D Printed Concrete:
The Influence of Process Parameters on Inter-Layer Adhesion - Yalçınkaya Çağlar (2022-03)
Influence of Hydroxypropyl Methylcellulose Dosage on the Mechanical Properties of 3D Printable Mortars with and without Fiber-Reinforcement - Zhang Hao, Zhu Liming, Zhang Fan, Yang Mijia (2021-04)
Effect of Fiber Content and Alignment on the Mechanical Properties of 3D Printing Cementitious Composites - Zhou Longfei, Gou Mifeng, Zhang Haibo (2022-12)
Investigation on the Applicability of Bauxite-Tailings as Fine Aggregate to Prepare 3D Printing Mortar
2 Citations
- Bradford Katy, Gentry Russell, Alon Lola, Kurtis Kimberly (2025-08)
Construction 3D Printing Material Selection:
Minimizing Cost and Carbon Footprint of Residential Wall Assemblies - Šahmenko Genādijs, Puzule Līga, Sapata Alise, Šlosbergs Pēteris et al. (2024-06)
Gypsum-Cement-Pozzolan Composites for 3D Printing:
Properties and Life Cycle Assessment
BibTeX
@article{genc_demi_beyh_kapl.2023.AotSaPoACRwCBB,
author = "Gokhan Genc and Ruya Kilic Demircan and Figen Beyhan and Gökhan Kaplan",
title = "Assessment of the Sustainability and Producibility of Adobe-Constructions Reinforced with Ca-Based Binders: Environmental Life-Cycle-Analysis and 3D Printability",
doi = "10.1016/j.scitotenv.2023.167695",
year = "2023",
journal = "Science of the Total Environment",
pages = "167695",
}
Formatted Citation
G. Genc, R. K. Demircan, F. Beyhan and G. Kaplan, “Assessment of the Sustainability and Producibility of Adobe-Constructions Reinforced with Ca-Based Binders: Environmental Life-Cycle-Analysis and 3D Printability”, Science of the Total Environment, p. 167695, 2023, doi: 10.1016/j.scitotenv.2023.167695.
Genc, Gokhan, Ruya Kilic Demircan, Figen Beyhan, and Gökhan Kaplan. “Assessment of the Sustainability and Producibility of Adobe-Constructions Reinforced with Ca-Based Binders: Environmental Life-Cycle-Analysis and 3D Printability”. Science of the Total Environment, 2023, 167695. https://doi.org/10.1016/j.scitotenv.2023.167695.