Printability and Early Mechanical Properties of Material-Composition Modified 3D Printing Engineered Cementitious Composites Based on the Response-Surface-Methodology (2023-09)¶
Zhu Lingli, , Zhao Yu, Ruan Wenqiang, Ge Yali,
Journal Article - Journal of Building Engineering, No. 107837
Abstract
To explore the influence mechanism between material composition and the early performance of 3D printing engineered cementitious composites (3DP-ECC). In this paper, the effects of different dosages of fly ash (FA), Sand and hydroxypropyl methylcellulose (HPMC) on the printability and early mechanical properties of 3DP-ECC were studied based on response surface method (RSM). The results revealed that with the increase of HPMC dosage, the yield stress and plastic viscosity gradually increased, and the mechanical properties initially increased and then decreased. With the increase of FA dosage, the yield stress initially decreased and then increased, and the plastic viscosity gradually decreased. At the same time, the compressive strength reduced and the tensile properties were improved. The optimal dosages of 28–29% FA, 0.545–0.550 sand to binder rate (S/B) and 0.302–0.305% HPMC were determined by RSM. It provided a theoretical basis for the calculation and analysis of ECC components and structures in 3D printing.
¶
26 References
- Abudawaba Fareh, Gomaa Eslam, Gheni Ahmed, Gawady Mohamed (2021-09)
Developing Mix Proportions for Class C Fly-Ash-Based Alkali-Activated 3D Printed Concrete Mixtures - Álvarez-Fernández Martina, Prendes-Gero María, González-Nicieza Celestino, Guerrero-Miguel Diego-José et al. (2021-02)
Optimum Mix-Design for 3D Concrete Printing Using Mining-Tailings:
A Case Study in Spain - Asprone Domenico, Menna Costantino, Bos Freek, Salet Theo et al. (2018-06)
Rethinking Reinforcement for Digital Fabrication with Concrete - Bos Freek, Kruger Jacques, Lucas Sandra, Zijl Gideon (2021-04)
Juxtaposing Fresh Material-Characterisation-Methods for Buildability-Assessment of 3D Printable Cementitious Mortars - Chen Mingxu, Li Laibo, Zheng Yan, Zhao Piqi et al. (2018-09)
Rheological and Mechanical Properties of Admixtures-Modified 3D Printing Sulphoaluminate Cementitious Materials - Jayathilakage Roshan, Rajeev Pathmanathan, Sanjayan Jay (2020-01)
Yield-Stress-Criteria to Assess the Buildability of 3D Concrete Printing - Khalil Noura, Aouad Georges, Cheikh Khadija, Rémond Sébastien (2017-09)
Use of Calcium-Sulfoaluminate-Cements for Setting-Control of 3D Printing Mortars - Le Thanh, Austin Simon, Lim Sungwoo, Buswell Richard et al. (2012-01)
Mix-Design and Fresh Properties for High-Performance Printing Concrete - Li Victor, Bos Freek, Yu Kequan, McGee Wesley et al. (2020-04)
On the Emergence of 3D Printable Engineered, Strain-Hardening Cementitious Composites - Liu Chao, Wang Xianggang, Chen Yuning, Zhang Chao et al. (2021-06)
Influence of Hydroxypropyl-Methylcellulose and Silica-Fume on Stability, Rheological Properties, and Printability of 3D Printing Foam-Concrete - Nguyen Vuong, Panda Biranchi, Zhang Guomin, Nguyen-Xuan Hung et al. (2021-01)
Digital Design Computing and Modelling for 3D Concrete Printing - Soltan Daniel, Li Victor (2018-03)
A Self-Reinforced Cementitious Composite for Building-Scale 3D Printing - Xu Jiabin, Chen Mingxu, Zhao Zhihui, Li Laibo et al. (2021-01)
Printability and Efflorescence-Control of Admixtures-Modified 3D Printed White Portland-Cement-Based Materials Based on the Response-Surface-Methodology - Xu Zhuoyue, Zhang Dawang, Li Hui, Sun Xuemei et al. (2022-05)
Effect of FA and GGBFS on Compressive Strength, Rheology, and Printing Properties of Cement-Based 3D Printing Material - Yalçınkaya Çağlar (2022-03)
Influence of Hydroxypropyl Methylcellulose Dosage on the Mechanical Properties of 3D Printable Mortars with and without Fiber-Reinforcement - Ye Junhong, Cui Can, Yu Jiangtao, Yu Kequan et al. (2021-02)
Effect of Polyethylene-Fiber Content on Workability and Mechanical-Anisotropic Properties of 3D Printed Ultra-High-Ductile Concrete - Yu Kequan, McGee Wesley, Ng Tsz, Zhu He et al. (2021-02)
3D Printable Engineered Cementitious Composites:
Fresh and Hardened Properties - Yuan Qiang, Gao Chao, Huang Tingjie, Zuo Shenghao et al. (2022-03)
Factors Influencing the Properties of Extrusion-Based 3D Printed Alkali-Activated Fly-Ash-Slag Mortar - Zhang Yifan, Aslani Farhad (2021-08)
Development of Fiber-Reinforced Engineered Cementitious Composite Using Polyvinyl-Alcohol-Fiber and Activated Carbon-Powder for 3D Concrete Printing - Zhang Yi, Jiang Zhengwu, Zhu Yanmei, Zhang Jie et al. (2020-10)
Effects of Redispersible Polymer-Powders on the Structural Build-Up of 3D Printing Cement Paste with and without Hydroxypropyl-Methylcellulose - Zhou Wen, Zhang Yamei, Ma Lei, Li Victor (2022-04)
Influence of Printing Parameters on 3D Printing Engineered Cementitious Composites - Zhu Binrong, Nematollahi Behzad, Pan Jinlong, Zhang Yang et al. (2021-04)
3D Concrete Printing of Permanent Formwork for Concrete Column Construction - Zhu Binrong, Pan Jinlong, Nematollahi Behzad, Zhou Zhenxin et al. (2019-07)
Development of 3D Printable Engineered Cementitious Composites with Ultra-High Tensile Ductility for Digital Construction - Zhu Binrong, Pan Jinlong, Zhou Zhenxin, Cai Jingming (2021-04)
Mechanical Properties of Engineered Cementitious Composites Beams Fabricated by Extrusion-Based 3D - Zhu Lingli, Yao Jie, Zhao Yu, Ruan Wenqiang et al. (2022-12)
Effects of Composite Cementation System on Rheological and Working Performances of Fresh 3D Printable Engineered Cementitious Composites - Zou Shuai, Xiao Jianzhuang, Duan Zhenhua, Ding Tao et al. (2021-10)
On Rheology of Mortar with Recycled Fine Aggregate for 3D Printing
4 Citations
- Abbas Yassir, Alsaif Abdulaziz (2025-11)
Explainable Data-Driven Modeling for Optimized Mix Design of 3D-Printed Concrete:
Interpreting Nonlinear Synergies Among Binder Components and Proportions - Zat Tuani, Schuster Sílvio, Schmitt Duarte Ester, Freitas Daudt Natália et al. (2025-03)
Rheological Properties of High-Performance Concrete Reinforced with Microfibers and Their Effects on 3D Printing Process - Araújo Rísia, Martinelli Antônio, Cabral Kleber, Nunes Ueslei et al. (2025-03)
Effect of Lightweight Expanded Clay Aggregate (LECA) On the Printability of Cementitious Compositions for 3D Printing - Du Guoqiang, Sun Yan, Qian Ye (2024-10)
Nature-Inspired Approach for Enhancing the Fracture Performance of 3D Printed Strain-Hardening Cementitious Composites (3DP-SHCC)
BibTeX
@article{zhu_yao_zhao_ruan.2023.PaEMPoMCM3PECCBotRSM,
author = "Lingli Zhu and Jie Yao and Yu Zhao and Wenqiang Ruan and Yali Ge and Xuemao Guan",
title = "Printability and Early Mechanical Properties of Material-Composition Modified 3D Printing Engineered Cementitious Composites Based on the Response-Surface-Methodology",
doi = "10.1016/j.jobe.2023.107837",
year = "2023",
journal = "Journal of Building Engineering",
pages = "107837",
}
Formatted Citation
L. Zhu, J. Yao, Y. Zhao, W. Ruan, Y. Ge and X. Guan, “Printability and Early Mechanical Properties of Material-Composition Modified 3D Printing Engineered Cementitious Composites Based on the Response-Surface-Methodology”, Journal of Building Engineering, p. 107837, 2023, doi: 10.1016/j.jobe.2023.107837.
Zhu, Lingli, Jie Yao, Yu Zhao, Wenqiang Ruan, Yali Ge, and Xuemao Guan. “Printability and Early Mechanical Properties of Material-Composition Modified 3D Printing Engineered Cementitious Composites Based on the Response-Surface-Methodology”. Journal of Building Engineering, 2023, 107837. https://doi.org/10.1016/j.jobe.2023.107837.