MgO/Fluid Catalytic Cracking Ash-Blends for 3D Printing on Vertical Surfaces (2023-10)¶
, Zhao Huanyu, , ,
Journal Article - Journal of Sustainable Cement-Based Materials, pp. 1-14
Abstract
Fluid catalytic cracking (FCC) ash is a common industrial waste in the crude oil refinery process. In this study, raw FCC ash was incorporated to develop sustainable MgO/FCC ash blends for 3D printing on vertical surfaces. Rheological and tack behaviors of MgO/FCC ash blends were systematically studied, followed by the assessment of mechanical property and hydration products. On this basis, the suitable mixture for 3D printing on the vertical surfaces was determined, and its feasibility was verified with lab-scale 3D printing. Finally, the environmental impact of the developed mixture was estimated through batch leaching and composition tests. This study provides an alternative method to upcycle FCC ash as an ingredient for 3D concrete printing, which brings benefits to both the construction and oil refinery industries. Besides, the rheological, tack, and hydration investigations of the MgO/FCC ash blends guide the future design of similar mixtures with upcycled wastes.
¶
18 References
- Carneau Paul, Mesnil Romain, Baverel Olivier, Roussel Nicolas (2022-03)
Layer Pressing in Concrete Extrusion-Based 3D Printing:
Experiments and Analysis - Chen Yu, Rodríguez Claudia, Li Zhenming, Chen Boyu et al. (2020-07)
Effect of Different Grade Levels of Calcined Clays on Fresh and Hardened Properties of Ternary-Blended Cementitious Materials for 3D Printing - Jenny Ercan, Lloret-Fritschi Ena, Jenny David, Sounigo Eliott et al. (2022-06)
Robotic Plaster Spraying:
Crafting Surfaces with Adaptive Thin-Layer Printing - Lu Bing, Li Mingyang, Lao Wenxin, Weng Yiwei et al. (2018-08)
Effect of Spray-Based Printing Parameters on Cementitious Material-Distribution - Lu Bing, Li Hongliang, Li Mingyang, Wong Teck et al. (2022-11)
Mechanism and Design of Fluid Catalytic Cracking Ash-Blended Cementitious Composites for High-Performance Printing - Lu Bing, Li Mingyang, Wong Teck, Qian Shunzhi (2021-02)
Effect of Printing Parameters on Material-Distribution in Spray-Based 3D Concrete Printing (S-3DCP) - Lu Bing, Li Mingyang, Wong Teck, Qian Shunzhi (2022-09)
Spray-Based 3D Concrete Printing with Calcium and Polymeric Additives:
A Feasibility Study - Lu Bing, Qian Ye, Li Mingyang, Weng Yiwei et al. (2019-04)
Designing Spray-Based 3D Printable Cementitious Materials with Fly-Ash-Cenosphere and Air-Entraining Agent - Lu Bing, Zhu Weiping, Weng Yiwei, Liu Zhixin et al. (2020-02)
Study of MgO-Activated-Slag as a Cementless Material for Sustainable Spray-Based 3D Printing - Tao Yaxin, Lesage Karel, Tittelboom Kim, Yuan Yong et al. (2021-11)
Influence of Substrate-Surface-Roughness and Moisture-Content on Tensile Adhesion Performance of 3D Printable Concrete - Ting Guan, Tay Yi, Qian Ye, Tan Ming (2019-03)
Utilization of Recycled Glass for 3D Concrete Printing:
Rheological and Mechanical Properties - Weng Yiwei, Lu Bing, Li Mingyang, Liu Zhixin et al. (2018-09)
Empirical Models to Predict Rheological Properties of Fiber-Reinforced Cementitious Composites for 3D Printing - Xiao Jianzhuang, Zou Shuai, Yu Ying, Wang Yu et al. (2020-09)
3D Recycled Mortar Printing:
System-Development, Process-Design, Material-Properties and On-Site-Printing - Yu Shiwei, Du Hongjian, Sanjayan Jay (2020-07)
Aggregate-Bed 3D Concrete Printing with Cement-Paste Binder - Yu Shiwei, Xia Ming, Sanjayan Jay, Yang Lin et al. (2021-07)
Microstructural Characterization of 3D Printed Concrete - Zhang Chao, Jia Zijian, Luo Zhe, Deng Zhicong et al. (2022-11)
Printability and Pore-Structure of 3D Printing Low-Carbon Concrete Using Recycled Clay-Brick-Powder with Various Particle-Features - Zhang Yi, Jiang Zhengwu, Zhu Yanmei, Zhang Jie et al. (2020-10)
Effects of Redispersible Polymer-Powders on the Structural Build-Up of 3D Printing Cement Paste with and without Hydroxypropyl-Methylcellulose - Zhang Yu, Zhang Yunsheng, Yang Lin, Liu Guojian et al. (2022-08)
Evaluation of Aggregates, Fibers and Voids-Distribution in 3D Printed Concrete
3 Citations
- Aman Abdulkerim, Yang Zhe, Xin Yubo, Zhang Xiaoman et al. (2025-04)
Introducing Magnesium Oxide into 3D Printed Concrete to Mitigate Dry-Shrinkage - Liu Xiongfei, Li Chuang, Guo Pei, Wang Li et al. (2025-02)
Spray-Based 3D Printed Tunnel Slag Concrete:
Evaluation for Printability and Mechanical Performance - Lu Bing, Wang Lining, Wang Xiangyu, Tan Ming et al. (2024-04)
Development of Robotic Sprayable Self-Sensing Cementitious Material for Smart Structural Health Monitoring
BibTeX
@article{lu_zhao_li_wong.2023.MFCCABf3PoVS,
author = "Bing Lu and Huanyu Zhao and Mingyang Li and Teck Neng Wong and Shunzhi Qian",
title = "MgO/Fluid Catalytic Cracking Ash-Blends for 3D Printing on Vertical Surfaces",
doi = "10.1080/21650373.2023.2270571",
year = "2023",
journal = "Journal of Sustainable Cement-Based Materials",
pages = "1--14",
}
Formatted Citation
B. Lu, H. Zhao, M. Li, T. N. Wong and S. Qian, “MgO/Fluid Catalytic Cracking Ash-Blends for 3D Printing on Vertical Surfaces”, Journal of Sustainable Cement-Based Materials, pp. 1–14, 2023, doi: 10.1080/21650373.2023.2270571.
Lu, Bing, Huanyu Zhao, Mingyang Li, Teck Neng Wong, and Shunzhi Qian. “MgO/Fluid Catalytic Cracking Ash-Blends for 3D Printing on Vertical Surfaces”. Journal of Sustainable Cement-Based Materials, 2023, 1–14. https://doi.org/10.1080/21650373.2023.2270571.