Skip to content

#type

Keywords by Co - Occurrence

  1. Lal Dhirajkumar, Rangari Vinay, Khare Karan (2026-03)
    Structural Optimization and Cost-Efficient Development of an Indigenous Gantry-Type 3D Concrete Printing System for Scalable Construction Applications
  2. Tafur Ginette, Rivera Cristhofer, Torres Pablo (2026-02)
    Evaluation of Sustainable 3D Concrete with Partial Replacement of Fine Aggregate by PET and Addition of Coconut Fibers:
    Impact on Construction with the Use of 3D Gantry-Type Printers in Peru
  3. Wen Kuo-Wei, Su Yen-Fang, Mo Kim, Hung Chung-Chan (2025-12)
    Time-Dependent Rheology, Green Strength, and Buildability of 3D-Printed Ultra-High Performance Concrete Incorporating Various Fiber Types and Contents
  4. Nguyen Trang, Park Jaejun, Kim Dong-Hyun (2025-11)
    Impacts of Infill Patterns and Curve Types in 3D Printed Clay Walls
  5. Varghese Renny, Rangel Bárbara, Maia Lino (2025-10)
    Strength, Structure, and Sustainability in 3D-Printed Concrete Using Different Types of Fiber Reinforcements
  6. Mercimek Ömer, Şahin Oğuzhan, Çelik Alper, Ozkan Ekinci Mehmet et al. (2025-08)
    Structural Performance of Pre-Fabricated 3D Printed Concrete Walls:
    Effect of Cold Joint, Axial Load and Load Type
  7. Surehali Sahil, Venkatachalam Akshay, Divigalpitiya Ranjith, Kumar Aditya et al. (2025-06)
    Ultra-Low Dosages of Novel Graphene Types Enhance the Rheological Properties and Buildability of 3D Printed Binders
  8. Yassin Ahmed, Hafez Mohamed, Aboelhassan Mohamed (2025-04)
    Experimental and Numerical Investigation on the Effect of Different Types of Synthetic Fibers on the Flexure Behavior and Mechanical Properties of 3D Cementitious Composite Printing Provided with Cement CEM II/A-P
  9. Mahmoudi Matineh, Wangler Timothy, Flatt Robert (2024-09)
    Robustness of Digital Concrete:
    Effects of Temperature, Accelerator Type and Dosage
  10. Hanratty Niall, Khan Mehran, McNally Ciaran (2024-07)
    The Role of Different Clay Types in Achieving Low-Carbon 3D Printed Concretes
  11. Luo Qiling, Yu Ke-Ke, Long Wujian, Zheng Shuyi et al. (2024-07)
    Influence of Different Types of Superabsorbent Polymers on Fresh Mechanical Properties and Inter-Layer Adhesion of 3D Printed Concrete
  12. Wang Xiaonan, Li Wengui, Guo Yipu, Kashani Alireza et al. (2024-04)
    Concrete 3D Printing Technology for Sustainable Construction:
    A Review on Raw Material, Concrete Type and Performance
  13. Chamatete Kunda, Yalçınkaya Çağlar (2024-03)
    Numerical Evaluation on Thermal Performance of 3D Printed Concrete Walls:
    The Effects of Lattice-Type, Filament-Width and Granular-Filling-Material
  14. Wang Xiaonan, Li Wengui, Guo Yipu, Kashani Alireza et al. (2024-02)
    Concrete 3D Printing Technology in Sustainable Construction:
    A Review on Raw Materials, Concrete Types and Performances
  15. Wang Yu, Rodriguez Fabian, Olek Jan, Zavattieri Pablo et al. (2023-11)
    Influence of Type of Fibers on Fresh and Hardened Properties of Three-Dimensional-Printed Cementitious Mortars
  16. Liu Xiaoshuang, Zou Yuxiao, Wu Yingxuan, Cui Dong et al. (2023-09)
    The Effect of U-Type Expanding Agent for Concrete (UEA) on the Microstructural and Mechanical Properties of Mortar Fabricated Through Alternate 3D Printing
  17. Ramezani Amir, Modaresi Shahriar, Dashti Pooria, Givkashi Mohammad et al. (2023-04)
    Effects of Different Types of Fibers on Fresh and Hardened Properties of Cement and Geopolymer-Based 3D Printed Mixtures:
    A Review
  18. Surehali Sahil, Tripathi Avinaya, Nimbalkar Atharwa, Neithalath Narayanan (2023-01)
    Anisotropic Chloride Transport in 3D Printed Concrete and Its Dependence on Layer-Height and Interface-Types
  19. Baek Seoung-Ho, Yang Jung-Ho, Ha Cheol-Woo, Shim Patrick et al. (2022-11)
    Design and Evaluation of Additive Manufactured Highly Efficient Inclined-Wing-Type Continuous Mixer
  20. Liu Miao, Wang Li, Ma Guowei, Li Weiwei et al. (2022-11)
    U-Type Steel-Wire-Mesh for the Flexural Performance Enhancement of 3D Printed Concrete:
    A Novel Reinforcing Approach
  21. Matthäus Carla, Back Daniel, Weger Daniel, Kränkel Thomas et al. (2020-07)
    Effect of Cement-Type and Limestone-Powder-Content on Extrudability of Lightweight Concrete
  22. Hass Lauri, Bos Freek (2020-07)
    Bending and Pull-Out Tests on a Novel Screw Type Reinforcement for Extrusion-Based 3D Printed Concrete
  23. Carstensen Josephine (2020-06)
    Topology-Optimization with Nozzle-Size-Restrictions for Material-Extrusion-Type Additive Manufacturing
  24. Secrieru Egor, Khodor Jad, Schröfl Christof, Mechtcherine Viktor (2018-05)
    Formation of Lubricating Layer and Flow Type During Pumping of Cement-Based Materials