A Feasibility Study on HPMC-Improved Sulphoaluminate Cement for 3D Printing (2018-11)¶
Ding Zhu, Wang Xiaodong, , , Ding Zhi-Kun
Journal Article - Materials, Vol. 11, Iss. 12
Abstract
A novel 3D printing material based on hydroxypropyl methylcellulose (HPMC)-improved sulphoaluminate cement (SAC) for rapid 3D construction printing application is reported. The hydration heat, setting time, fluidity of paste and mortar, shape retainability, and compressive strength of extruded SAC mortar were investigated. HPMC dosage, water-to-cement (W/C) ratio, and sand-to-cement (S/C) ratio were studied as the experimental parameters. Hydration heat results reveal HPMC could delay the hydration of SAC. The initial and final setting time measured using Vicat needle would be shortened in the case of W/C ratio of 0.3 and 0.35 with HPMC dosage from 0.5% to 1.5%, W/C ratio of 0.40 with HPMC dosage of 0.5%, 0.75%, and 1.5%, and W/C ratio of 0.45 with HPMC dosage of 0.45, or be extended in the case of W/C ratio of 0.4 with HPMC dosage of 1.0% and W/C ratio of 0.45 with HPMC dosage from 0.75% to 1.5%. Fluidity measurement shows HPMC significantly improves the shape retainability. Furthermore, the addition of HPMC remarkably increased the compressive strength of extruded mortar. The results showed that HPMC could be used to prepare 3D printing SAC having satisfactory shape retainability, setting time and compressive strength.
¶
7 References
- Bos Freek, Wolfs Robert, Ahmed Zeeshan, Salet Theo (2016-08)
Additive Manufacturing of Concrete in Construction:
Potentials and Challenges of 3D Concrete Printing - Ma Guowei, Wang Li (2017-08)
A Critical Review of Preparation Design and Workability Measurement of Concrete Material for Large-Scale 3D Printing - Panda Biranchi, Paul Suvash, Mohamed Nisar, Tay Yi et al. (2017-09)
Measurement of Tensile Bond Strength of 3D Printed Geopolymer Mortar - Panda Biranchi, Tan Ming (2018-03)
Experimental Study on Mix Proportion and Fresh Properties of Fly-Ash-Based Geopolymer for 3D Concrete Printing - Paul Suvash, Zijl Gideon, Tan Ming, Gibson Ian (2018-05)
A Review of 3D Concrete Printing Systems and Materials Properties:
Current Status and Future Research Prospects - Perkins Isaac, Skitmore Martin (2015-03)
Three-Dimensional Printing in the Construction Industry:
A Review - Perrot Arnaud, Rangeard Damien, Courteille Eric (2018-04)
3D Printing of Earth-Based Materials:
Processing Aspects
22 Citations
- Wang Qingwei, Han Song, Liu Qi, Yang Junhao et al. (2024-12)
Research on the 3D Printing Process and Filament Shape of Cementitious Materials in Low Gravity - Antoni Antoni, Adi N., Kurniawan M., Agraputra A. et al. (2023-06)
The Influence of Viscosity-Modifying Agent and Calcium-Carbonate on 3D Printing Mortar Characteristics - Panda Biranchi, Tran Jonathan (2023-03)
Material-Design, Additive Manufacturing, and Performance of Cement-Based Materials - Waqar Ahsan, Othman Idris, Pomares Juan (2023-02)
Impact of 3D Printing on the Overall Project Success of Residential Construction Projects Using Structural Equation Modelling - Peng Yiming, Unluer Cise (2022-12)
Development of Alternative Cementitious Binders for 3D Printing Applications:
A Critical Review of Progress, Advantages and Challenges - Liu Qiang, Jiang Quan, Huang Mojia, Xin Jie et al. (2022-03)
Modifying Effect of Anionic Polyacrylamide Dose for Cement-Based 3DP Materials:
Printability and Mechanical Performance Tests - Yalçınkaya Çağlar (2022-03)
Influence of Hydroxypropyl Methylcellulose Dosage on the Mechanical Properties of 3D Printable Mortars with and without Fiber-Reinforcement - Liu Junli, Nguyen Vuong, Panda Biranchi, Fox Kate et al. (2022-02)
Additive Manufacturing of Sustainable Construction Materials and Form-Finding Structures:
A Review on Recent Progresses - Wang Hailong, Shao Jianwen, Zhang Jing, Zou Daoqin et al. (2021-11)
Bond Shear Performances and Constitutive Model of Interfaces Between Vertical and Horizontal Filaments of 3D Printed Concrete - Sun Xiaoyan, Zhou Jiawei, Wang Qun, Shi Jiangpeng et al. (2021-11)
PVA-Fiber-Reinforced High-Strength Cementitious Composite for 3D Printing:
Mechanical Properties and Durability - Shahzad Qamar, Shen Junyi, Naseem Rabia, Yao Yonggang et al. (2021-10)
Influence of Phase-Change-Material on Concrete Behavior for Construction 3D Printing - Wi Kwangwoo, Wang Kejin, Taylor Peter, Laflamme Simon et al. (2021-09)
Properties and Microstructure of Extrusion-Based 3D Printing Mortar Containing a Highly Flowable, Rapid Set Grout - Salman Nazar, Ma Guowei, Ijaz Nauman, Wang Li (2021-04)
Importance and Potential of Cellulosic Materials and Derivatives in Extrusion-Based 3D Concrete Printing:
Prospects and Challenges - Vallurupalli Kavya, Farzadnia Nima, Khayat Kamal (2021-01)
Effect of Flow Behavior and Process-Induced Variations on Shape Stability of 3D Printed Elements:
A Review - Mohan Manu, Rahul Attupurathu, Schutter Geert, Tittelboom Kim (2021-01)
Early-Age Hydration, Rheology and Pumping Characteristics of CSA Cement-Based 3D Printable Concrete - Kristombu Baduge Shanaka, Navaratnam Satheeskumar, Zidan Yousef, McCormack Tom et al. (2021-01)
Improving Performance of Additive Manufactured Concrete:
A Review on Material Mix-Design, Processing, Inter-Layer Bonding, and Reinforcing-Methods - Afarani Hajar, Carroll William, Garboczi Edward, Biernacki Joseph (2020-11)
Designing 3D Printable Cementitious Materials with Gel-Forming Polymers - Sun Xiaoyan, Gao Chao, Wang Hailong (2020-10)
Bond-Performance Between BFRP-Bars and 3D Printed Concrete - Sun Xiaoyan, Wang Qun, Wang Hailong, Chen Long (2020-03)
Influence of Multi-Walled Nanotubes on the Fresh and Hardened Properties of a 3D Printing PVA Mortar Ink - Khalil Abdullah, Wang Xiangyu, Celik Kemal (2020-02)
3D Printable Magnesium Oxide Concrete:
Towards Sustainable Modern Architecture - Panda Biranchi, Mohamed Nisar, Paul Suvash, Bhagath Singh Gangapatnam et al. (2019-07)
The Effect of Material Fresh Properties and Process Parameters on Buildability and Inter-Layer Adhesion of 3D Printed Concrete - Chen Yu, Figueiredo Stefan, Yalçınkaya Çağlar, Çopuroğlu Oğuzhan et al. (2019-04)
The Effect of Viscosity-Modifying Admixture on the Extrudability of Limestone and Calcined-Clay-Based Cementitious Material for Extrusion-Based 3D Concrete Printing
BibTeX
@article{ding_wang_sanj_zou.2018.AFSoHISCf3P,
author = "Zhu Ding and Xiaodong Wang and Jay Gnananandan Sanjayan and Patrick X. W. Zou and Zhi-Kun Ding",
title = "A Feasibility Study on HPMC-Improved Sulphoaluminate Cement for 3D Printing",
doi = "10.3390/ma11122415",
year = "2018",
journal = "Materials",
volume = "11",
number = "12",
}
Formatted Citation
Z. Ding, X. Wang, J. G. Sanjayan, P. X. W. Zou and Z.-K. Ding, “A Feasibility Study on HPMC-Improved Sulphoaluminate Cement for 3D Printing”, Materials, vol. 11, no. 12, 2018, doi: 10.3390/ma11122415.
Ding, Zhu, Xiaodong Wang, Jay Gnananandan Sanjayan, Patrick X. W. Zou, and Zhi-Kun Ding. “A Feasibility Study on HPMC-Improved Sulphoaluminate Cement for 3D Printing”. Materials 11, no. 12 (2018). https://doi.org/10.3390/ma11122415.