Skip to content

Investigation into the Effect of Delays Between Printed Layers on the Mechanical Strength of Inkjet 3DP Mortar (2019-11)

10.1016/j.mfglet.2019.11.004

 Shakor Pshtiwan,  Nejadi Shami,  Paul Gavin
Journal Article - Manufacturing Letters, Vol. 23, pp. 19-22

Abstract

Currently, additive manufacturing have enabled to fabricate the three-dimensional models. 3D-Printing technique is a multipurpose process for producing structural members using a sequential layering approach. The “feature quality” of 3DP specimens can be improved by optimising the build constraints. In this paper, a mortar mix powder-base has been prepared that consists of cementitious materials. Experiments are conducted to investigate the effects of different delays in printing time on the mechanical properties of the scaffolds. It has been shown that the compressive stress and strength of printed specimens with a delay of 200ms were greater than specimens with other delay values.

4 References

  1. Gibbons Gregory, Williams Reuben, Purnell Phil, Farahi Elham (2013-07)
    3D Printing of Cement Composites
  2. Pierre Alexandre, Weger Daniel, Perrot Arnaud, Lowke Dirk (2018-01)
    Penetration of Cement-Pastes into Sand-Packings During 3D Printing:
    Analytical and Experimental Study
  3. Shakor Pshtiwan, Nejadi Shami, Paul Gavin, Malek Sardar (2019-01)
    Review of Emerging Additive Manufacturing Technologies in 3D Printing of Cementitious Materials in the Construction Industry
  4. Shakor Pshtiwan, Sanjayan Jay, Nazari Ali, Nejadi Shami (2017-02)
    Modified 3D Printed Powder to Cement-Based Material and Mechanical Properties of Cement Scaffold Used in 3D Printing

6 Citations

  1. Liu Junxing, Li Peiqi, Piao Taiyan, Im Sumin et al. (2024-12)
    High-Alumina Cementitious Materials for Binder-Jetting 3D Printing:
    Exploring Suitable Mixing-Ratio and Curing-Solution for Improving Mechanical Properties and Hydration-Reaction
  2. Panda Biranchi, Shakor Pshtiwan, Laghi Vittoria (2023-12)
    Powder-Bed Additive Manufacturing
  3. Puzatova (nee Sharanova) Anastasiia, Shakor Pshtiwan, Laghi Vittoria, Dmitrieva Maria (2022-11)
    Large-Scale 3D Printing for Construction Application by Means of Robotic Arm and Gantry 3D Printer:
    A Review
  4. Shakor Pshtiwan, Chu Shaohua, Puzatova (nee Sharanova) Anastasiia, Dini Enrico (2022-01)
    Review of Binder-Jetting 3D Printing in the Construction Industry
  5. Shakor Pshtiwan, Gowripalan Nadarajah, Rasouli Habib (2021-03)
    Experimental and Numerical Analysis of 3D Printed Cement Mortar Specimens Using Inkjet 3DP
  6. Li Zhanzhao, Hojati Maryam, Wu Zhengyu, Piasente Jonathon et al. (2020-07)
    Fresh and Hardened Properties of Extrusion-Based 3D Printed Cementitious Materials:
    A Review

BibTeX 
@article{shak_neja_paul.2020.IitEoDBPLotMSoI3M,
  author            = "Pshtiwan N. Shakor and Shami Nejadi and Gavin Paul",
  title             = "Investigation into the Effect of Delays Between Printed Layers on the Mechanical Strength of Inkjet 3DP Mortar",
  doi               = "10.1016/j.mfglet.2019.11.004",
  year              = "2020",
  journal           = "Manufacturing Letters",
  volume            = "23",
  pages             = "19--22",
}
Formatted Citation

P. N. Shakor, S. Nejadi and G. Paul, “Investigation into the Effect of Delays Between Printed Layers on the Mechanical Strength of Inkjet 3DP Mortar”, Manufacturing Letters, vol. 23, pp. 19–22, 2020, doi: 10.1016/j.mfglet.2019.11.004.

Shakor, Pshtiwan N., Shami Nejadi, and Gavin Paul. “Investigation into the Effect of Delays Between Printed Layers on the Mechanical Strength of Inkjet 3DP Mortar”. Manufacturing Letters 23 (2020): 19–22. https://doi.org/10.1016/j.mfglet.2019.11.004.